Home » Cisco Manuals » Networking » Cisco AS5400XM » Manual Viewer

Cisco AS5400XM Installation Guide - Page 83

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide,

UPC - 746320997261

Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Chapter 7 Troubleshooting Monitoring the Chassis Environment Temperature at outlet is measured as 74C/165F. Temperature State: Temperature is in critical state. DFC Busyout/Power-down: A DFC is powered down. Slot:1, Type:NP108 DFC A DFC is busyout. Slot:2, Type:T1 8 PRI DFC A DFC is busyout. Slot:3, Type:NP108 DFC Fans: Fans temperature delta is measured as 6C. All fans are running well. Power Supply: Redundant Power System is present. RPS Input Voltage status: normal RPS Output Voltage status: normal RPS Fan status: normal RPS Thermal status: normal RPS OverVoltage status: normal Environmental monitor experienced the following events: Temperature:sensor failed. Fans:monitor dropped. Temperature:warning. Temperature:sensor recovered. Fans:monitor recovered. Fans:normal. Temperature:critical. • The output shown below displays on your console when the system reaches a shutdown state: Router# show environment Temperature: Temperature Reading: Temperature at inlet is measured as 70C/158F. Temperature at outlet is measured as 82C/179F. Temperature State: Temperature is in shutdown state. DFC Busyout/Power-down: A DFC is powered down. Slot:1, Type:NP108 DFC A DFC is powered down. Slot:2, Type:T1 8 PRI DFC A DFC is powered down. Slot:3, Type:NP108 DFC Fans: Fans temperature delta is measured as 6C. All fans are running well. Power Supply: Redundant Power System is present. RPS Input Voltage status: normal RPS Output Voltage status: normal RPS Fan status: normal RPS Thermal status: normal RPS OverVoltage status: normal Environmental monitor experienced the following events: Temperature:sensor failed. Fans:monitor dropped. Temperature:warning. Temperature:sensor recovered. Fans:monitor recovered. Fans:normal. Temperature:critical. Temperature:shutdown. 78-17406-01 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide 7-9

Section	Page
Contents	3
Preface	7
Document Organization	7
Document Conventions	8
Obtaining Documentation	14
Cisco.com	14
Product Documentation DVD	14
Ordering Documentation	14
Documentation Feedback	14
Cisco Product Security Overview	15
Reporting Security Problems in Cisco Products	15
Obtaining Technical Assistance	16
Cisco Technical Support & Documentation Website	16
Submitting a Service Request	17
Definitions of Service Request Severity	17
Obtaining Additional Publications and Information	18
Safety Warnings, Recommendations, and Tools Required	21
General Safety	21
Maintaining Safety with Electricity	22
Preventing Electrostatic Discharge	23
Required Tools and Equipment	23
Where to Go Next	24
Feature Card and Carrier Card Guidelines	25
Overview	25
Online Insertion and Removal of Feature Cards	26
Removing and Installing Populated Carrier Cards	26
Removing a Populated Carrier Card	27
Installing a Populated Carrier Card	29
Getting Help	31
Where to Go Next	31
T1 and E1 Feature Cards	33
Overview	33
Online Installation and Removal of the T1 or E1 Feature Card	34
Removing the T1 or E1 Feature Card	35
Online Insertion and Removal Example for the T1 or E1 Feature Card	38
Installing the T1 or E1 Feature Card	41
Configuring Input Impedance for the E1 Feature Card	43
Configuration	43
Verification	44
Getting Help	44
Where to Go Next	44
Channelized T3 Feature Card	45
Overview	45
Online Insertion and Removal of the CT3 Feature Card	46
Removing the CT3 Feature Card	46
Installing the CT3 Feature Card	49
Getting Help	51
Where to Go Next	51
Universal Port and Dial-Only Feature Cards	53
Overview	53
Restrictions for the Universal Port and Dial-Only Feature Cards	54
Online Insertion and Removal of the Universal Port or Dial-Only Feature Card	55
Removing the Universal Port or Dial-Only Feature Card	55
Online Insertion and Removal Example for the Universal Port or Dial-Only Feature Card	58
Installing the Universal Port or Dial-Only Feature Card	60
System Processing Engine Firmware	62
Getting Help	62
Where to Go Next	62
Voice Feature Card	63
Overview	63
Restrictions for the Voice Feature Card	64
Online Insertion and Removal of the Voice Feature Card	65
Removing the Voice Feature Card	65
Online Insertion and Removal Example for the Voice Feature Card	68
Installing the Voice Feature Card	69
Replacing PVDM2 Modules in the Voice Feature Card	70
Orienting the PVDM2 Module During Installation	71
Removing PVDM2 Modules From the Voice Feature Card	71
Installing PVDM2 Modules in the Voice Feature Card	72
Digital Signal Processor Firmware	73
Getting Help	73
Where to Go Next	73
Troubleshooting	75
LEDs	75
Mixing WAN Feature Cards	79
Mixing Universal Port and Dial-Only Feature Cards	80
Mixing Voice Feature Cards With Universal Port and Dial-Only Feature Cards	80
Monitoring the Chassis Environment	81
Displaying Environment Status	82
Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards	84
Using Drop and Insert Mode on the CT3 Feature Card	84
Troubleshooting Network Interfaces	85
Getting Help	85
Cabling Specifications	87
2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts	87
8-Port T1 or E1 Feature Card Cable and Port Pinouts	92
Attaching the 8-Port T1 or E1 Feature Card Interface Cable to a Bracket (Optional)	94
CT3 Feature Card Cable and Port Pinouts	98
Bantam Jack Port Pinouts	99