Home » Cisco Manuals » Networking » Cisco AS5400XM » Manual Viewer

Cisco AS5400XM Installation Guide - Page 85

Troubleshooting Network Interfaces, Getting Help

UPC - 746320997261

Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Chapter 7 Troubleshooting Troubleshooting Network Interfaces Note The port-number is the T1 circuit that you wish to drop. T1 port numbers range from 1 to 28. Step 2 Disable drop and insert mode after testing the T1 circuits. Note We recommend that you disable drop and insert mode to prevent accidental use of the push button on the CT3 feature card. To disable drop and insert mode, enter the test trunk drop-insert off port-number privileged EXEC command as follows: Router> test trunk drop-insert off port-number Troubleshooting Network Interfaces For information about isolating problems with the network connections to your universal gateway, see the Internetwork Troubleshooting Guide publication available on Cisco.com. Getting Help For information about technical support, onsite service, and exchange and repair services, see the "Obtaining Technical Assistance" section on page xvi. 78-17406-01 Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide 7-11

Section	Page
Contents	3
Preface	7
Document Organization	7
Document Conventions	8
Obtaining Documentation	14
Cisco.com	14
Product Documentation DVD	14
Ordering Documentation	14
Documentation Feedback	14
Cisco Product Security Overview	15
Reporting Security Problems in Cisco Products	15
Obtaining Technical Assistance	16
Cisco Technical Support & Documentation Website	16
Submitting a Service Request	17
Definitions of Service Request Severity	17
Obtaining Additional Publications and Information	18
Safety Warnings, Recommendations, and Tools Required	21
General Safety	21
Maintaining Safety with Electricity	22
Preventing Electrostatic Discharge	23
Required Tools and Equipment	23
Where to Go Next	24
Feature Card and Carrier Card Guidelines	25
Overview	25
Online Insertion and Removal of Feature Cards	26
Removing and Installing Populated Carrier Cards	26
Removing a Populated Carrier Card	27
Installing a Populated Carrier Card	29
Getting Help	31
Where to Go Next	31
T1 and E1 Feature Cards	33
Overview	33
Online Installation and Removal of the T1 or E1 Feature Card	34
Removing the T1 or E1 Feature Card	35
Online Insertion and Removal Example for the T1 or E1 Feature Card	38
Installing the T1 or E1 Feature Card	41
Configuring Input Impedance for the E1 Feature Card	43
Configuration	43
Verification	44
Getting Help	44
Where to Go Next	44
Channelized T3 Feature Card	45
Overview	45
Online Insertion and Removal of the CT3 Feature Card	46
Removing the CT3 Feature Card	46
Installing the CT3 Feature Card	49
Getting Help	51
Where to Go Next	51
Universal Port and Dial-Only Feature Cards	53
Overview	53
Restrictions for the Universal Port and Dial-Only Feature Cards	54
Online Insertion and Removal of the Universal Port or Dial-Only Feature Card	55
Removing the Universal Port or Dial-Only Feature Card	55
Online Insertion and Removal Example for the Universal Port or Dial-Only Feature Card	58
Installing the Universal Port or Dial-Only Feature Card	60
System Processing Engine Firmware	62
Getting Help	62
Where to Go Next	62
Voice Feature Card	63
Overview	63
Restrictions for the Voice Feature Card	64
Online Insertion and Removal of the Voice Feature Card	65
Removing the Voice Feature Card	65
Online Insertion and Removal Example for the Voice Feature Card	68
Installing the Voice Feature Card	69
Replacing PVDM2 Modules in the Voice Feature Card	70
Orienting the PVDM2 Module During Installation	71
Removing PVDM2 Modules From the Voice Feature Card	71
Installing PVDM2 Modules in the Voice Feature Card	72
Digital Signal Processor Firmware	73
Getting Help	73
Where to Go Next	73
Troubleshooting	75
LEDs	75
Mixing WAN Feature Cards	79
Mixing Universal Port and Dial-Only Feature Cards	80
Mixing Voice Feature Cards With Universal Port and Dial-Only Feature Cards	80
Monitoring the Chassis Environment	81
Displaying Environment Status	82
Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards	84
Using Drop and Insert Mode on the CT3 Feature Card	84
Troubleshooting Network Interfaces	85
Getting Help	85
Cabling Specifications	87
2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts	87
8-Port T1 or E1 Feature Card Cable and Port Pinouts	92
Attaching the 8-Port T1 or E1 Feature Card Interface Cable to a Bracket (Optional)	94
CT3 Feature Card Cable and Port Pinouts	98
Bantam Jack Port Pinouts	99