Cisco SPA2102-NA User Guide - Page 21

Placing the Phone Adapter, Wall-Mount Option

Get Cisco SPA2102-NA PDF manuals and user guides View all Cisco SPA2102-NA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Placing the Phone Adapter Phone Adapter with Router There are two ways to place the Phone Adapter. The first way is to place the Phone Adapter horizontally on a surface. The second way is to mount the Phone Adapter on a wall. The wall-mount option is explained in further detail below. Wall-Mount Option The Phone Adapter has two wall-mount slots on its back panel. The distance between the two slots is 58 mm (2.28 inches). 1. Determine where you want to mount the Phone Adapter. 2. Drill two holes into the wall. Make sure the holes are 58 mm (2.28 inches) apart. 3. Insert a screw into each hole, and leave 5 mm (0.2 inches) of its head exposed. 4. Maneuver the Phone Adapter so the wall-mount slots line up with the two screws. 5. Place the wall-mount slots over the screws and slide the Phone Adapter down until the screws fit snugly into the wall-mount slots. Congratulations! The installation of the Phone Adapter is complete. Figure 4-10: Measurement between Wall-Mount Slots Chapter 4: Getting Started 13 Placing the Phone Adapter

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Phone Adapter with Router
13
Chapter 4: Getting Started
Placing the Phone Adapter
Placing the Phone Adapter
There are two ways to place the Phone Adapter. The first way is to place the Phone Adapter horizontally on a
surface. The second way is to mount the Phone Adapter on a wall. The wall-mount option is explained in further
detail below.
Wall-Mount Option
The Phone Adapter has two wall-mount slots on its back panel. The distance between the two slots is 58 mm
(2.28 inches).
1.
Determine where you want to mount the Phone Adapter.
2.
Drill two holes into the wall. Make sure the holes are 58 mm (2.28 inches) apart.
3.
Insert a screw into each hole, and leave 5 mm (0.2 inches) of its head exposed.
4.
Maneuver the Phone Adapter so the wall-mount slots line up with the two screws.
5.
Place the wall-mount slots over the screws and slide the Phone Adapter down until the screws fit snugly into
the wall-mount slots.
Congratulations! The installation of the Phone Adapter is complete.
Figure 4-10: Measurement between
Wall-Mount Slots