Cisco VG224 Hardware Installation Guide - Page 51

Connecting the Analog Voice Interface to a Distribution Panel - amphenol

Get Cisco VG224 - Analog Phone Gateway PDF manuals and user guides
UPC - 746320575360
View all Cisco VG224 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Chapter 3 Installing the Cisco VG224 Voice Gateway Connecting Cables Connecting the Analog Voice Interface to a Distribution Panel To connect the multiport analog voice interface to a distribution panel, which connects to telephones, faxes, or analog PBX equipment, use the following procedure. (See Figure 3-14.) Cable Use an RJ-21 cable with Amphenol 50-pin connectors (not included). For RJ-21X/CA21A pinouts, see Table A-5 on page A-6 in Appendix A, "Cable Specifications and Information." Warning This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming call. Statement 1042 Procedure Step 1 Connect the RJ-21 cable from the analog voice multiport to the distribution panel. Step 2 Secure the cable in place using the strap. Figure 3-14 Analog Voice Connection 103118 VG224-24FXS RJ-21 cable Distribution panel OL-5006-04 Cisco VG224 Voice Gateway Hardware Installation Guide 3-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
3-19
Cisco VG224 Voice Gateway Hardware Installation Guide
OL-5006-04
Chapter 3
Installing the Cisco VG224 Voice Gateway
Connecting Cables
Connecting the Analog Voice Interface to a Distribution Panel
To connect the multiport analog voice interface to a distribution panel, which connects to telephones,
faxes, or analog PBX equipment, use the following procedure. (See
Figure 3-14
.)
Cable
Use an RJ-21 cable with Amphenol 50-pin connectors (not included).
For RJ-21X/CA21A pinouts, see
Table A-5 on page A-6
in
Appendix A, “Cable Specifications and
Information.”
Warning
This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do
not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11
port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming
call.
Statement 1042
Procedure
Step 1
Connect the RJ-21 cable from the analog voice multiport to the distribution panel.
Step 2
Secure the cable in place using the strap.
Figure 3-14
Analog Voice Connection
103118
RJ-21 cable
Distribution panel
VG224-24FXS