Compaq DL580 Service Guide - Page 42

Processor, Loosen the retention screw - xeon

Get Compaq DL580 - ProLiant - 1 GB RAM PDF manuals and user guides
UPC - 720591733483
View all Compaq DL580 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

2-26 Compaq ProLiant DL580 Server Maintenance and Service Guide Processor To remove a processor: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the top access panel. See "Top Access Panel" earlier in this chapter. 3. Loosen the retention screw . 4. Pull up both ejector levers . 5. Lift the processor out of the processor slot . 2 2 1 3 Figure 2-19. Removing a processor Reverse steps 1 through 5 to replace a processor. The processor is keyed to ensure correct alignment. IMPORTANT: When installing a server with Pentium III Xeon processors running at speeds of 550 MHz or greater in Compaq Rack 7000 series racks (part numbers 165753-001 [42U] and 163747-001 [22U]), the new processor technology requires the installation of a new Compaq High Airflow Rack Door Insert (part number 327281-B21 [single] or 327281-B22 [6-pack] for 42U racks, and 157847-B21 [single] or 157847-B22 [6-pack] for 22U racks). NOTE: This notice applies to servers with Pentium III Xeon processors running at 550 MHz or greater that are installed in 7000 series racks. Compaq servers based on other processor technologies (including Pentium III Xeon processors) do not require any rack changes.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
2-26
Compaq ProLiant DL580 Server Maintenance and Service Guide
Processor
To remove a processor:
1. Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2. Remove the top access panel. See
“
Top Access Panel
”
earlier in this chapter.
3. Loosen the retention screw
.
4. Pull up both ejector levers
.
5. Lift the processor out of the processor slot
.
2
3
2
1
Figure 2-19.
Removing a processor
Reverse steps 1 through 5 to replace a processor. The processor is keyed to ensure
correct alignment.
IMPORTANT:
When installing a server with Pentium III Xeon processors running at speeds of 550 MHz
or greater in Compaq Rack 7000 series racks (part numbers 165753-001 [42U] and 163747-001 [22U]),
the new processor technology requires the installation of a new Compaq High Airflow Rack Door Insert
(part number 327281-B21 [single] or 327281-B22 [6-pack] for 42U racks, and 157847-B21 [single] or
157847-B22 [6-pack] for 22U racks).
NOTE:
This notice applies to servers with Pentium III Xeon processors running at 550 MHz or greater
that are installed in 7000 series racks. Compaq servers based on other processor technologies (including
Pentium III Xeon processors) do not require any rack changes.