Compaq DL580 Service Guide - Page 83

with the Memory Address Range of an ISA Card. Check the Memory Address

Get Compaq DL580 - ProLiant - 1 GB RAM PDF manuals and user guides
UPC - 720591733483
View all Compaq DL580 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

3-14 Compaq ProLiant DL580 Server Maintenance and Service Guide Table 3-2 POST Error Messages continued Error Code Audible Beeps Probable Source of Problem 1761-Fixed Disk 1 None does not support Block Mode Hard drive error 1764-Slot x Drive Array - Capacity Expansion Process is temporarily disabled (followed by any one of these statements): Expansion will resume when Array Accelerator has been reattached. Expansion will resume when Array Accelerator has been replaced. Expansion will resume when Array Accelerator RAM allocation is successful. Expansion will resume when Array Accelerator battery reaches full charge. Expansion will resume when automatic data recovery has been completed. 1765-Slot x Drive Array Option ROM Appears to Conflict with an ISA Card. ISA cards with 16-bit memory cannot be configured in memory range C0000 to DFFFF along with the SMART-2/E 8-bit Option ROM due to EISA bus limitations. Please remove or reconfigure the ISA card. 1766-Slot x Drive Array requires System ROM Upgrade. Run Systems ROMPaq Utility. 1767-Slot x Drive Array Option ROM is Not Programmed Correctly or may Conflict with the Memory Address Range of an ISA Card. Check the Memory Address Configuration of installed ISA Card(s) or run Options ROMPaq Utility to attempt SMART-2/E Option ROM Reprogramming. 1768-Slot x Drive None Array-Resuming logical drive expansion process. 1769-Slot x Drive None Array - Drive(s) disabled due to failure during expand. Select F1 to continue with logical drives disabled. Select F2 to accept data loss and to re-enable logical drives. SMART-2 Controller error SMART-2 Controller error. Data has been lost while expanding the array; therefore, the drives have been temporarily disabled. Recommended Action Run the System Configuration Utility and correct. Reattach or replace array accelerator, wait until the array accelerator batteries have charged, or for Automatic Data Recovery to complete, as indicated. Remove or reconfigure conflicting ISA cards. Disable "shared memory" on any ISA network cards that may be installed. Run the latest Systems ROMPaq Utility to upgrade the System ROMs. Remove or reconfigure conflicting ISA cards, especially any cards that are not recognized by the System Configuration Utility. Try reprogramming the ROM on the SMART-2/E Controller using the latest Options ROMPaq (version 2.29 or higher). No action required. Displays whenever a controller reset or power cycle occurs while array expansion is in progress. Press F2 to accept the data loss and re-enable the logical drives. Restore data from backup. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
3-14
Compaq ProLiant DL580 Server Maintenance and Service Guide
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1761-Fixed Disk 1
does not support
Block Mode
None
Hard drive error
Run the System Configuration
Utility and correct.
1764-Slot
x
Drive Array
–
Capacity Expansion Process is temporarily disabled
(followed by any one of these statements):
■
Expansion will resume when Array Accelerator has been reattached.
■
Expansion will resume when Array Accelerator has been replaced.
■
Expansion will resume when Array Accelerator RAM allocation is successful.
■
Expansion will resume when Array Accelerator battery reaches full charge.
■
Expansion will resume when automatic data recovery has been completed.
Reattach or replace array
accelerator, wait until the array
accelerator batteries have
charged, or for Automatic Data
Recovery to complete, as
indicated.
1765-Slot
x
Drive Array Option ROM Appears to Conflict with an ISA Card. ISA
cards with 16-bit memory cannot be configured in memory range C0000 to DFFFF
along with the SMART-2/E 8-bit Option ROM due to EISA bus limitations. Please
remove or reconfigure the ISA card.
Remove or reconfigure
conflicting ISA cards. Disable
“
shared memory
”
on any ISA
network cards that may be
installed.
1766-Slot
x
Drive Array requires System ROM Upgrade. Run Systems ROMPaq
Utility.
Run the latest Systems ROMPaq
Utility to upgrade the System
ROMs.
1767-Slot
x
Drive Array Option ROM is Not Programmed Correctly or may Conflict
with the Memory Address Range of an ISA Card. Check the Memory Address
Configuration of installed ISA Card(s) or run Options ROMPaq Utility to attempt
SMART-2/E Option ROM Reprogramming.
Remove or reconfigure
conflicting ISA cards, especially
any cards that are not
recognized by the System
Configuration Utility. Try
reprogramming the ROM on the
SMART-2/E Controller using the
latest Options ROMPaq
(version 2.29 or higher).
1768-Slot
x
Drive
Array-Resuming
logical drive
expansion process.
None
SMART-2 Controller error
No action required. Displays
whenever a controller reset or
power cycle occurs while array
expansion is in progress.
1769-Slot
x
Drive
Array
–
Drive(s)
disabled due to
failure during
expand. Select F1 to
continue with logical
drives disabled.
Select F2 to accept
data loss and to
re-enable logical
drives.
None
SMART-2 Controller error. Data
has been lost while expanding
the array; therefore, the drives
have been temporarily disabled.
Press
F2
to accept the data loss
and re-enable the logical drives.
Restore data from backup.
continued