Compaq Portable 286 Compaq Portable Computer, Compaq Plus Personal Computer, a - Page 100

NOTE: For COMPAQ Portable and COMPAQ PLUS Personal Computers with serial

Get Compaq Portable 286 - Notebook PC PDF manuals and user guides View all Compaq Portable 286 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

To remove the monitor enclosure assembly: 1. Complete the removal procedures for all installed controller and option boards (see Section 7.9). 2. Remove mass storage device Enclosure A (see Section 7.11). 3. Remove the fan/bracket assembly (see Section 7.8). NOTE: For COMPAQ Portable and COMPAQ PLUS Personal Computers with serial numbers below 1524020B0001, it is necessary to remove the power switch filter assembly INSTEAD of the fan/bracket assembly. You do not have to remove the power supply. 4. Using the special two piece socket power supply removal tool or box end wrench, remove the two screws that secure the monitor enclosure to the wall of the power supply subsystem area (Figure 7.12-2). 5. Place the computer on the work surface so that the handle is facing up and the side of the computer with feet is facing you. 6. Remove the system board connector access plate (see Section 7.7). 7. Disconnect the speaker connector from the system board. Cut any cable ties that hold the speaker cable in place (Figure 7.12-3). NOTE: On the COMPAQ PORTABLE 286, remove the monitor power connector from the system board. 8. Locate and remove the two screws that secure the monitor enclosure to the

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
To remove the monitor enclosure assembly:
1. Complete the removal procedures for all installed controller and option
boards (see Section 7.9).
2. Remove mass storage device Enclosure A (see Section 7.11).
3. Remove the fan/bracket assembly (see Section 7.8).
NOTE: For COMPAQ Portable and COMPAQ PLUS Personal Computers with serial
numbers below 1524020B0001, it is necessary to remove the power
switch filter assembly INSTEAD of the fan/bracket assembly. You do
not have to remove the power supply.
4. Using the special two piece socket power supply removal tool or box end
wrench, remove the two screws that secure the monitor enclosure to the
wall of the power supply subsystem area (Figure 7.12-2).
5. Place the computer on the work surface so that the handle is facing up and
the side of the computer with feet is facing you.
6. Remove the system board connector access plate (see Section 7.7).
7. Disconnect the speaker connector from the system board. Cut any cable
ties that hold the speaker cable in place (Figure 7.12-3).
NOTE: On the COMPAQ PORTABLE 286, remove the monitor power connector from
the system board.
8. Locate and remove the two screws that secure the monitor enclosure to the