Compaq Portable 286 Compaq Portable Computer, Compaq Plus Personal Computer, a - Page 102

Keyboard Assembly Removal and Replacement

Get Compaq Portable 286 - Notebook PC PDF manuals and user guides View all Compaq Portable 286 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

12. For the COMPAQ Portable and COMPAQ PLUS Personal Computers, disconnect the power cable connector from the sweep board. 13. To remove the monitor enclosure from the chassis: a. Carefully slide the monitor enclosure away from the power supply subsystem until the enclosure clears the tab in the back corner of the monitor. Then slide the enclosure back until the front of the enclosure clears the chassis (Figure 7.12-5). b. Lift the monitor enclosure up and out of the chassis and rest one edge on the chassis. Carefully pull the monitor power cable through the hole in the floor of the monitor assembly. Lift the monitor enclosure away from the computer and set it aside. To replace the monitor enclosure, reverse Steps 1 through 13. Chapter 7.13 Keyboard Assembly Removal and Replacement To remove the keyboard assembly: 1. Complete the removal procedure for the system board connector access plate (see Section 7.7). 2. Cut the tie wrap that secures the keyboard cable to the chassis and disconnect the keyboard cable from the system board (Figure 7.13-1).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
12. For the COMPAQ Portable and COMPAQ PLUS Personal Computers, disconnect
the power cable connector from the sweep board.
13. To remove the monitor enclosure from the chassis:
a. Carefully slide the monitor enclosure away from the power supply
subsystem until the enclosure clears the tab in the back corner of
the monitor. Then slide the enclosure back until the front of the
enclosure clears the chassis (Figure 7.12-5).
b. Lift the monitor enclosure up and out of the chassis and rest one
edge on the chassis. Carefully pull the monitor power cable through
the hole in the floor of the monitor assembly. Lift the monitor
enclosure away from the computer and set it aside.
To replace the monitor enclosure, reverse Steps 1 through 13.
Chapter 7.13 Keyboard Assembly Removal and Replacement
To remove the keyboard assembly:
1. Complete the removal procedure for the system board connector access plate
(see Section 7.7).
2. Cut the tie wrap that secures the keyboard cable to the chassis and
disconnect the keyboard cable from the system board (Figure 7.13-1).