Compaq Portable 286 Compaq Portable Computer, Compaq Plus Personal Computer, a - Page 78

Complete the Board Slots Access Plate Removal procedure see

Get Compaq Portable 286 - Notebook PC PDF manuals and user guides View all Compaq Portable 286 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

To remove the fixed disk drive controller board: 1. Complete the Board Slots Access Plate Removal procedure (see Section 7.4). 2. Disconnect the two fixed disk drive controller board signal cables by pulling the connectors away from the board (Figure 7.9-2). CAUTION Pull only on the connector, do not pry. Pulling on the wire makes the connector grip the pins tighter, which will damage the connector 3. Remove the retaining screw that secures the fixed disk drive controller board. Gently pull the board up and out of its J103 socket on the system board and out of the computer. (Figure 7.9-3).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
To remove the fixed disk drive controller board:
1. Complete the Board Slots Access Plate Removal procedure (see Section 7.4).
2. Disconnect the two fixed disk drive controller board signal cables by
pulling the connectors away from the board (Figure 7.9-2).
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
CAUTION
Pull only on the connector, do not pry. Pulling on the wire makes the
connector grip the pins tighter, which will damage the connector.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
3. Remove the retaining screw that secures the fixed disk drive controller
board. Gently pull the board up and out of its J103 socket on the system
board and out of the computer. (Figure 7.9-3).