Compaq Portable 286 Compaq Portable Computer, Compaq Plus Personal Computer, a - Page 99

Monitor Enclosure Removal and Replacement, 1524020B0001 and above

Get Compaq Portable 286 - Notebook PC PDF manuals and user guides View all Compaq Portable 286 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

To replace Device 1A, reverse Step 10. To replace Enclosure A, reverse Steps 1 through 8 CAUTION On COMPAQ PORTABLE 286 Personal Computers, three bottom mounting screws are used to secure Enclosure A. These screws are shorter than those used in Enclosure B. To avoid damaging the drives, return the correct screws to the correct locations when replacing the drive assemblies Chapter 7.12 Monitor Enclosure Removal and Replacement The redesign of the COMPAQ Portable Computer chassis required a redesign of the monitor enclosure (Figure 7.12-1). This new design of the monitor enclosure (PN 105034-001 no longer available) is used in COMPAQ Portable Computers with the serial number 1524020B0001 and above, and all COMPAQ PORTABLE 286 Personal Computers. DO NOT use the previous monitor enclosure (PN 100481-001 no longer available) in the computers mentioned above. NOTE: To prevent possible mistakes in replacing the monitor enclosure, a tab has been placed on the chassis near the fan/bracket assembly to allow ONLY monitor enclosures with this new design to be installed. Using the previous monitor enclosure may result in power supply failure.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
To replace Device 1A, reverse Step 10.
To replace Enclosure A, reverse Steps 1 through 8.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
CAUTION
On COMPAQ PORTABLE 286 Personal Computers, three bottom mounting screws are
used to secure Enclosure A. These screws are shorter than those used in
Enclosure B. To avoid damaging the drives, return the correct screws to the
correct locations when replacing the drive assemblies.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Chapter 7.12 Monitor Enclosure Removal and Replacement
The redesign of the COMPAQ Portable Computer chassis required a redesign of
the monitor enclosure (Figure 7.12-1).
This new design of the monitor enclosure (PN 105034-001 no longer
available) is used in COMPAQ Portable Computers with the serial number
1524020B0001 and above, and all COMPAQ PORTABLE 286 Personal Computers.
DO NOT use the previous monitor enclosure (PN 100481-001 no longer
available) in the computers mentioned above.
NOTE: To prevent possible mistakes in replacing the monitor enclosure, a
tab has been placed on the chassis near the fan/bracket assembly to
allow ONLY monitor enclosures with this new design to be installed.
Using the previous monitor enclosure may result in power supply
failure.