Compaq Portable 286 Compaq Portable Computer, Compaq Plus Personal Computer, a - Page 93

Mass Storage Device Enclosure A Removal and Replacement, To replace Enclosure B

Get Compaq Portable 286 - Notebook PC PDF manuals and user guides View all Compaq Portable 286 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

10. If Enclosure B contains a fixed disk drive, disconnect the fixed disk drive LED connector from the front of the enclosure and remove this enclosure from the system chassis (Figure 7.11-5). NOTE: If Enclosure B is a fixed disk drive replacement for a COMPAQ Portable or COMPAQ PLUS Personal Computer, it may be necessary to remove the face plate/LED assembly that is attached to the chassis. To do this, remove the hex nut at the bottom of the face plate/LED assembly before removing Enclosure B. To replace Enclosure B, reverse Steps 1 through 10 CAUTION When removing the enclosure, do not bend the drive ground strap located on the top front shock mount of each enclosure Mass Storage Device Enclosure A Removal and Replacement To remove Enclosure A: 1. Complete the removal procedures for all installed controller and expansion boards (see Section 7.9). 2. Remove the mass storage device access plate (see Section 7.11). 3. Disconnect the power cables from the mass storage device(s).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
10. If Enclosure B contains a fixed disk drive, disconnect the fixed disk
drive LED connector from the front of the enclosure and remove this
enclosure from the system chassis (Figure 7.11-5).
NOTE: If Enclosure B is a fixed disk drive replacement for a COMPAQ Portable
or COMPAQ PLUS Personal Computer, it may be necessary to remove the face
plate/LED assembly that is attached to the chassis. To do this, remove the
hex nut at the bottom of the face plate/LED assembly before removing
Enclosure B.
To replace Enclosure B, reverse Steps 1 through 10.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
CAUTION
When removing the enclosure, do not bend the drive ground strap located on the
top front shock mount of each enclosure.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Mass Storage Device Enclosure A Removal and Replacement
To remove Enclosure A:
1. Complete the removal procedures for all installed controller and expansion
boards (see Section 7.9).
2. Remove the mass storage device access plate (see Section 7.11).
3. Disconnect the power cables from the mass storage device(s).