Compaq Portable 286 Compaq Portable Computer, Compaq Plus Personal Computer, a - Page 81

J102 on COMPAQ PORTABLE 286 Personal Computers; J104 on COMPAQ Portable

Get Compaq Portable 286 - Notebook PC PDF manuals and user guides View all Compaq Portable 286 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

CAUTION Pull only on the connector, do not pry. Pulling on the wires damages the cable 4. Gently pull the video display controller board up and out of its socket (J102 on COMPAQ PORTABLE 286 Personal Computers; J104 on COMPAQ Portable and COMPAQ PLUS Personal Computers) on the system board and out of the computer (Figure 7.9-5). To replace the video display controller board, reverse Steps 1 through 4. NOTE: Be sure that the board is in the board guide on the left. Diskette/Tape Controller Board Removal and Replacement To remove the diskette/tape controller board: 1. Complete the Board Slots Access Plate Removal procedure (see Section 7.4). 2. Disconnect the fixed disk drive controller board signal cables, if installed (Figure 7.9-2).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
CAUTION
Pull only on the connector, do not pry. Pulling on the wires damages the
cable.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
4. Gently pull the video display controller board up and out of its socket
(J102 on COMPAQ PORTABLE 286 Personal Computers; J104 on COMPAQ Portable
and COMPAQ PLUS Personal Computers) on the system board and out of the
computer (Figure 7.9-5).
To replace the video display controller board, reverse Steps 1 through 4.
NOTE: Be sure that the board is in the board guide on the left.
Diskette/Tape Controller Board Removal and Replacement
To remove the diskette/tape controller board:
1. Complete the Board Slots Access Plate Removal procedure (see Section 7.4).
2. Disconnect the fixed disk drive controller board signal cables, if
installed (Figure 7.9-2).