Compaq Portable 286 Compaq Portable Computer, Compaq Plus Personal Computer, a - Page 74

board standoffs disengage. This releases the power supply assembly

Get Compaq Portable 286 - Notebook PC PDF manuals and user guides View all Compaq Portable 286 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

CAUTION Pull only on the connector, do not pry. Pulling on the wires makes the connector grip the pins tighter, which will damage the connector 3. Using the special two piece socket tool or 5/16 inch box end wrench, loosen the power supply mounting screw from the upper (or lower) right corner of the power supply assembly (Figure 7.8-20). 4. Partially close the access door panel to allow the standoffs to disengage the chassis. 5. Slide the power supply assembly toward the back of the chassis until the board standoffs disengage. This releases the power supply assembly from the chassis. 6. Carefully lift the power supply assembly out of the chassis and gently disconnect the remaining connector from the board (Figure 7.8-21).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
CAUTION
Pull only on the connector, do not pry. Pulling on the wires makes the
connector grip the pins tighter, which will damage the connector.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
3. Using the special two piece socket tool or 5/16 inch box end wrench,
loosen the power supply mounting screw from the upper (or lower) right
corner of the power supply assembly (Figure 7.8-20).
4. Partially close the access door panel to allow the standoffs to disengage
the chassis.
5. Slide the power supply assembly toward the back of the chassis until the
board standoffs disengage. This releases the power supply assembly
from the chassis.
6. Carefully lift the power supply assembly out of the chassis and gently
disconnect the remaining connector from the board (Figure 7.8-21).