Home » D-Link Manuals » Wireless » D-Link DWL-8500AP » Manual Viewer

D-Link DWL-8500AP Product Manual - Page 140

Set Security to Static WEP, VAP Commands

UPC - 790069297212

Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

D-Link Unified Access Point Administrator's Guide Table 39. VAP Commands Action Set the VLAN ID for a VAP on one radio Note: This example uses radio 1. For radio 2, use wlan1 View the wireless network name (SSID) Set the SSID Note: For VAP 0, use wlanx, where x is the radio. For VAPs 17, use wlanxvapy, where x is the radio, and y is the VAP ID. Get the current security mode Get detailed description of current security settings Set security to plain text Set security to static WEP Set security to IEEE 802.1X Set security to WPA/WPA2 Personal (PSK) Set security to WPA/WPA2 Enterprise (RADIUS) Command set vap with radio wlan0 to vlan-id Example: set vap vap4 with radio wlan0 to vlan-id 123 For VAP 0 on radio 1: get interface wlan0 ssid For VAP 3 on radio 2: get interface wlan1vap3 ssid set interface wlan0 ssid For example: set interface wlan0 ssid Engineering set interface wlan0 ssid "Engineering's AP" For VAP 3 on radio 2: set interface wlan1vap3 ssid Engineering For VAP 0 on radio 1: get interface wlan0 security For VAP 3 on radio 2: get interface wlan1vap3 security For VAP 0 on radio 1: get interface wlan0 detail For VAP 3 on radio 2: get interface wlan1vap3 detail set interface wlan0 security plain-text set interface wlan1vap3 security plain-text See the detailed example in "Set Security to Static WEP" on page 140. See detailed example in See "Set Security to IEEE 802.1X" on page 142. See detailed example in "Set Security to WPA/WPA2 Personal (PSK)" on page 143 See detailed example in "Set Security to WPA/WPA2 Enterprise (RADIUS)" on page 144 Set Security to Static WEP To configure Static WEP as the security mode, you need to issue multiple commands. This section describes the commands and procedures to configure Static WEP. NOTE: This example shows how to configure static WEP on VAP 0 on radio 1 (wlan0). For interface commands on VAPs 1-7, use wlanxvapy, where x is the radio, and y is the VAP ID. For example, to configure security on VAP 3 on radio 2, use wlan1vap3 instead of wlan0 in all of the following commands. 1. Set the security mode. DLINK-AP# set interface wlan0 security static-wep 2. Set the Transfer Key Index. The range for the transfer key index is 1-4. The following command sets the Transfer Key 140 © 2001-2008 D-Link Corporation. All Rights Reserved.

Section	Page
Unified Access Point (AP) Administrator’s Guide	1
Table of Contents	3
List of Figures	7
List of Tables	9
About This Document	11
Document Organization	11
Audience	11
Document Conventions	11
Online Help, Supported Browsers, and Limitations	12
Overview of the D-Link Access Point	15
Features and Benefits	16
IEEE Standards Support	16
Wireless Features	16
Security Features	17
Networking	17
Maintainability	17
Access Point Hardware	18
Preparing to Install the Access Point	19
Default Settings for the Unified Access Points	19
Administrator’s Computer Requirements	21
Wireless Client Requirements	22
Dynamic and Static IP Addressing on the AP	23
Recovering an IP Address	23
Discovering a Dynamically Assigned IP Address	23
Using the Reset Button	23
Installing the Access Point	25
Installing the Unified Access Point	25
Viewing Basic Settings	29
Using the CLI to View the IP Address	30
Configuring the Ethernet Interface	31
Using the Web UI to configure Ethernet Settings	31
Using the CLI to Configure Ethernet Settings	33
Configuring IEEE 802.1X Authentication	34
Using the Web UI to Configure 802.1X Authentication Information	35
Using the CLI to Configure 802.1X Authentication Information	36
Verifying the Installation	36
Configuring Access Point Security	39
Understanding Security on Wireless Networks	39
Choosing a Security Mode	39
Comparing Security Modes	40
When to Use Unencrypted (No Security)	40
When to Use Static WEP	40
When to Use IEEE 802.1X	41
When to Use WPA Personal	42
When to Use WPA Enterprise	42
Enabling Station Isolation	43
Configuring Virtual Access Point Security	43
None (Plain-text)	45
Static WEP	45
Static WEP Rules	48
Example of Using Static WEP	48
IEEE 802.1X	49
WPA Personal	50
WPA Enterprise	52
Prohibiting the SSID Broadcast	53
Managing the Access Point	55
Setting the Wireless Interface	55
Using the 802.11h Wireless Mode	57
Configuring Radio Settings	58
Configuring Virtual Access Points	62
Controlling Access by MAC Authentication	66
Configuring a MAC Filter List on the AP	66
Configuring MAC Authentication on the RADIUS Server	67
Configuring Load Balancing	68
Configuring Access Point Services	69
Configuring Quality of Service (QoS)	69
Understanding QoS	69
QoS and Load Balancing	69
802.11e and WMM Standards Support	70
QoS Queues and Parameters to Coordinate Traffic Flow	70
QoS Queues and Diff-Serve Code Points (DSCP) on Packets	70
EDCF Control of Data Frames and Arbitration Interframe Spaces	71
Random Backoff and Minimum / Maximum Contention Windows	72
Packet Bursting for Better Performance	73
Transmission Opportunity (TXOP) Interval for Client Stations	73
802.1p and DSCP tags	73
Configuring QoS Settings	75
Enabling the Network Time Protocol Server	79
Enabling or Disabling a Network Time Protocol (NTP) Server	80
Maintaining the Access Point	81
Managing the Configuration File	81
Resetting the Factory Default Configuration	82
Saving the Current Configuration to a Backup File	83
Restoring the Configuration from a Previously Saved File	83
Rebooting the Access Point	85
Upgrading the Firmware	85
Configuring the Access Point for Managed Mode	87
Transitioning Between Modes	87
Configuring Managed Access Point Settings	88
Viewing Managed AP DHCP Information	89
Viewing Access Point Status	91
Viewing Interface Status	91
Ethernet (Wired) Settings	92
Wireless Settings	92
Viewing Events Logs	92
Configuring Persistent Logging Options	93
Configuring the Log Relay Host for Kernel Messages	94
Example of Using Linux syslogd	94
Enabling or Disabling the Log Relay Host on the Events Page	95
Viewing Transmit and Receive Statistics	95
Viewing Client Association Information	97
Link Integrity Monitoring	98
Viewing Neighboring Access Points	98
Wireless Client Settings and RADIUS Server Setup	101
Accessing Wireless Client Security Settings	102
Configuring a Client to Access an Unsecure Network	104
Configuring Static WEP Security on a Client	104
Configuring WPA/WPA2 Personal on a Client	106
Using an External Authentication Server	108
Configuring IEEE 802.1X Security on a Client	108
IEEE 802.1X Client Using EAP/TLS Certificate	108
Configuring WPA/WPA2 Enterprise (RADIUS)	111
WPA/WPA2 Enterprise (RADIUS) Client Using EAP/PEAP	111
WPA/WPA2 Enterprise (RADIUS) Client Using EAP-TLS Certificate	113
Configuring the RADIUS Server for Authentication	116
Obtaining a TLS-EAP Certificate for a Client	119
Configuring the RADIUS Server for VLAN Tags	122
CLI for AP Configuration	125
How to Access the Access Point CLI	125
Telnet Connection to the AP	125
SSH Connection to the AP	126
Commands and Syntax	127
Using the get Command	128
Using the set Command	128
Using the add Command	129
Using the remove Command	129
Additional CLI Commands	130
Getting Help on Commands at the CLI	130
Tab Completion	130
Keyboard Shortcuts	131
Interface Naming Conventions	132
Saving Configuration Changes	133
Access Point CLI Commands	134
Configuring Basic Settings	134
Status	135
Ethernet Settings	136
Wireless Interface	137
Radio Settings	138
Virtual Access Points	139
Set Security to Static WEP	140
Set Security to IEEE 802.1X	142
Set Security to WPA/WPA2 Personal (PSK)	143
Set Security to WPA/WPA2 Enterprise (RADIUS)	144
Managed Access Point	146
IEEE 802.1X Supplicant Authentication	147
Quality of Service	147
Time	149
System Management	150
CLI Classes and Properties Reference	150

Match case Limit results 1 per page

140

D-Link Unified Access Point Administrator’s Guide

Set Security to Static WEP

To configure Static WEP as the security mode, you need to issue multiple commands. This

section describes the commands and procedures to configure Static WEP.

NOTE:

This example shows how to configure static WEP on VAP 0 on radio 1

(

wlan0

). For interface commands on VAPs 1-7, use

wlan

vap

, where

the radio, and

is the VAP ID. For example, to configure security on VAP 3

on radio 2, use

wlan1vap3

instead of

wlan0

in all of the following

commands.

Set the security mode.

DLINK-AP#

set interface wlan0 security static-wep

Set the Transfer Key Index.

The range for the transfer key index is 1-4. The following command sets the Transfer Key

Set the VLAN ID for a VAP on

one radio

Note:

This example uses radio 1.

For radio 2, use

wlan1

set vap

<vapID>

with radio wlan0 to vlan-id

<vlan_id>

Example:

set vap vap4 with radio wlan0 to vlan-id 123

View the wireless network name

(SSID)

For VAP 0 on radio 1:

get interface wlan0 ssid

For VAP 3 on radio 2:

get interface wlan1vap3 ssid

Set the SSID

Note:

For VAP 0, use

wlan

where

is the radio. For VAPs 1-

7, use

wlan

vap

, where

is the

radio, and

is the VAP ID.

set interface wlan0 ssid

<ssid_name>

For example:

set interface wlan0 ssid Engineering

set interface wlan0 ssid “Engineering’s AP”

For VAP 3 on radio 2:

set interface wlan1vap3 ssid Engineering

Get the current security mode

For VAP 0 on radio 1:

get interface wlan0 security

For VAP 3 on radio 2:

get interface wlan1vap3 security

Get detailed description of current

security settings

For VAP 0 on radio 1:

get interface wlan0 detail

For VAP 3 on radio 2:

get interface wlan1vap3 detail

Set security to plain text

set interface wlan0 security plain-text

set interface wlan1vap3 security plain-text

Set security to static WEP

See the detailed example in

“Set Security to Static WEP”

page 140.

Set security to IEEE 802.1X

See detailed example in See

“Set Security to IEEE 802.1X”

page 142.

Set security to WPA/WPA2

Personal (PSK)

See detailed example in

“Set Security to WPA/WPA2 Personal

(PSK)”

on page 143

Set security to WPA/WPA2

Enterprise (RADIUS)

See detailed example in

“Set Security to WPA/WPA2

Enterprise (RADIUS)”

on page 144

Table 39.

VAP Commands

Action

Command