Dell Dimension 2200 Dell Dimension 2200 Owner's Manual - Page 77

Removing Cards, Remove the screw from the card bracket.

Get Dell Dimension 2200 PDF manuals and user guides View all Dell Dimension 2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Removing Cards CAUTION: Before you begin any of the procedures in this section, follow the safety instructions on page 9. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. 1 Shut down the computer (see page 20). 2 Turn off any attached devices and disconnect them from their electrical outlets. NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network wall jack. 3 Disconnect the computer power cable from the wall outlet, and then press the power button to ground the system board. 4 Remove the computer cover (see page 60). 5 Rotate the power supply (see page 62). 6 Disconnect any cables connected to the card. 7 Remove the screw from the card bracket. 8 Grasp the card by its top corners, and lift it from the system board. 9 If you are removing the card permanently, reinstall a filler bracket. 10 Rotate the power supply back into place (see page 64). 11 Replace the computer cover (see page 80). 12 Plug your computer and devices into their electrical outlets, and turn them on. Adding Pa rts 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Adding Parts
77
Removing Cards
CAUTION: Before you begin any of the procedures in this section,
follow the safety instructions on page 9.
CAUTION: To guard against electrical shock, always unplug your
computer from the electrical outlet before opening the cover.
1
Shut down the computer (see page 20).
2
Turn off any attached devices and disconnect them from their
electrical outlets.
NOTICE:
To disconnect a network cable, first unplug the cable from your
computer and then unplug it from the network wall jack.
3
Disconnect the computer power cable from the wall outlet, and then
press the power button to ground the system board.
4
Remove the computer cover (see page 60).
5
Rotate the power supply (see page 62).
6
Disconnect any cables connected to the card.
7
Remove the screw from the card bracket.
8
Grasp the card by its top corners, and lift it from the system board.
9
If you are removing the card permanently, reinstall a filler bracket.
10
Rotate the power supply back into place (see page 64).
11
Replace the computer cover (see page 80).
12
Plug your computer and devices into their electrical outlets, and turn
them on.