Dell Inspiron 16 5640 Owners Manual - Page 50

Fan, Removing the fan

Get Dell Inspiron 16 5640 PDF manuals and user guides View all Dell Inspiron 16 5640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Steps 1. Using the alignment posts and rubber grommets, place the speakers in the slots on the palm-rest and keyboard assembly. NOTE: Ensure that the rubber grommets on the speakers are threaded through the alignment posts and the four rubber grommets are seated into the slot and installed on the speakers properly. Figure 24. Aligning the speaker grommets 2. Route the speaker cable along the routing guides on the palm-rest and keyboard assembly, over the wireless-antenna cables. Then secure the speaker cable within the routing guides on the palm-rest and keyboard assembly. NOTE: The speaker cable must be routed through the routing guides to avoid damaging the speaker cable when installing the base cover. 3. Connect the speaker cable to the connector (SPK) on the system board. 4. Connect the battery cable to the connector (BATT) on the system board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Fan Removing the fan Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task The following image indicates the location of the fan and provides a visual representation of the removal procedure. 50 Removing and installing Customer Replaceable Units (CRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Steps
1.
Using the alignment posts and rubber grommets, place the speakers in the slots on the palm-rest and keyboard assembly.
NOTE:
Ensure that the rubber grommets on the speakers are threaded through the alignment posts and the four rubber
grommets are seated into the slot and installed on the speakers properly.
Figure 24. Aligning the speaker grommets
2.
Route the speaker cable along the routing guides on the palm-rest and keyboard assembly, over the wireless-antenna cables.
Then secure the speaker cable within the routing guides on the palm-rest and keyboard assembly.
NOTE:
The speaker cable must be routed through the routing guides to avoid damaging the speaker cable when
installing the base cover.
3.
Connect the speaker cable to the connector (SPK) on the system board.
4.
Connect the battery cable to the connector (BATT) on the system board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Fan
Removing the fan
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
About this task
The following image indicates the location of the fan and provides a visual representation of the removal procedure.
50
Removing and installing Customer Replaceable Units (CRUs)