Dell Inspiron 16 5640 Owners Manual - Page 80

Installing the power-adapter port

Get Dell Inspiron 16 5640 PDF manuals and user guides View all Dell Inspiron 16 5640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task The following images indicate the location of the power-adapter port and provide a visual representation of the removal procedure. Figure 54. Removing the power-adapter port Steps 1. Remove the two (M2.5x5) screws that secure the right-display hinge to the system board and the palm-rest and keyboard assembly. 2. Using a plastic scribe, lift the right-display hinge to an angle of 90 degrees from the palm-rest and keyboard assembly to access the power-adapter port. 3. Disconnect the power-adapter port cable from the connector (DCIN) on the system board. 4. Remove the power-adapter port cable from the routing guide on the palm-rest and keyboard assembly. 5. Remove the power-adapter port from the slot on the palm-rest and keyboard assembly. Installing the power-adapter port CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. 80 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
About this task
The following images indicate the location of the power-adapter port and provide a visual representation of the removal
procedure.
Figure 54. Removing the power-adapter port
Steps
1.
Remove the two (M2.5x5) screws that secure the right-display hinge to the system board and the palm-rest and keyboard
assembly.
2.
Using a plastic scribe, lift the right-display hinge to an angle of 90 degrees from the palm-rest and keyboard assembly to
access the power-adapter port.
3.
Disconnect the power-adapter port cable from the connector (DCIN) on the system board.
4.
Remove the power-adapter port cable from the routing guide on the palm-rest and keyboard assembly.
5.
Remove the power-adapter port from the slot on the palm-rest and keyboard assembly.
Installing the power-adapter port
CAUTION:
The information in this section is intended for authorized service technicians only.
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
80
Removing and installing Field Replaceable Units (FRUs)