Dell PowerEdge R440 EMC Installation and Service Manual 1 - Page 103

M.2 SSD module, Installing the M.2 SSD module

Get Dell PowerEdge R440 PDF manuals and user guides View all Dell PowerEdge R440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Figure 74. Installing PERC card into internal PERC riser Next steps 1. Install the internal PERC riser. 2. Install the air shroud. 3. Follow the procedure listed in After working inside your system. M.2 SSD module NOTE: The write-protect switch is on the IDSDM or vFlash module. Installing the M.2 SSD module Prerequisites 1. Follow the safety guidelines listed in Safety instructions 2. Remove the air shroud. 3. Remove the BOSS card. NOTE: The procedure to remove the BOSS card is similar to the removing an expansion card. Steps 1. Connect the M.2 SSD module to the connector on the BOSS card. 2. Place the retention strap on the M.2 SSD module, and tighten the screw to secure the module. Installing and removing system components 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Figure 74. Installing PERC card into internal PERC riser
Next steps
1.
Install the internal PERC riser.
2.
Install the air shroud.
3.
Follow the procedure listed in
After working inside your system
.
M.2 SSD module
NOTE:
The write-protect switch is on the IDSDM or vFlash module.
Installing the M.2 SSD module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
2.
Remove the air shroud
.
3.
Remove the BOSS card.
NOTE:
The procedure to remove the BOSS card is similar to the
removing an expansion card
.
Steps
1.
Connect the M.2 SSD module to the connector on the BOSS card.
2.
Place the retention strap on the M.2 SSD module, and tighten the screw to secure the module.
Installing and removing system components
103