Dell PowerEdge R440 EMC Installation and Service Manual 1 - Page 110

Installing the LOM riser card

Get Dell PowerEdge R440 PDF manuals and user guides View all Dell PowerEdge R440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Figure 81. Removing LOM riser card Next steps Install the LOM riser card. Installing the LOM riser card Prerequisites Follow the safety guidelines listed in Safety instructions Steps 1. Align the connectors on the LOM riser card with the slot on the system. 2. Press the LOM riser card until the card is firmly seated on the system board connector and the two blue plastic snap hold the LOM riser card in place. 3. Using a Phillips #2 screwdriver, replace the screws to secure the LOM riser card to the system board. Figure 82. Installing LOM riser card Next steps 1. If removed, install the risers. 2. Follow the procedure listed in After working inside your system 110 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Figure 81. Removing LOM riser card
Next steps
Install the LOM riser card.
Installing the LOM riser card
Prerequisites
Follow the safety guidelines listed in
Safety instructions
Steps
1.
Align the connectors on the LOM riser card with the slot on the system.
2.
Press the LOM riser card until the card is firmly seated on the system board connector and the two blue plastic snap hold the LOM
riser card in place.
3.
Using a Phillips #2 screwdriver, replace the screws to secure the LOM riser card to the system board.
Figure 82. Installing LOM riser card
Next steps
1.
If removed, install the risers.
2.
Follow the procedure listed in
After working inside your system
110
Installing and removing system components