Dell PowerVault NX200 Hardware Owner's Manual - Page 38

NVRAM_CLR jumper, Using the System Setup

Get Dell PowerVault NX200 PDF manuals and user guides View all Dell PowerVault NX200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Table 1-2. System Messages (continued) Message Causes Corrective Actions Caution! NVRAM_CLR jumper is installed on system board NVRAM_CLR jumper is installed in the clear setting. CMOS has been cleared. Move the NVRAM_CLR jumper to the default position (pins 3 and 5). See Figure 6-1 for jumper location. Restart the system and re-enter the BIOS settings. See "Using the System Setup Program and UEFI Boot Manager" on page 51. CPU set to minimum frequency. The processor speed may be If not an intentional setting, intentionally set lower for check any other system power conservation. messages for possible causes. CPU x installed with no memory. Memory modules are required but not installed in the indicated processor's memory slots. Install memory modules for the processor. See "Expansion Cards" on page 103. Current boot mode The system failed to boot is set to UEFI. because UEFI boot mode Please ensure is enabled in BIOS and compatible the boot operating system bootable media is is non-UEFI. available. Use the system setup program to change the boot mode as needed. Ensure that the boot mode is set correctly and that the proper bootable media is available. See "Using the System Setup Program and UEFI Boot Manager" on page 51. Decreasing Faulty or improperly available memory installed memory modules. Reseat the memory modules. See "Troubleshooting System Memory" on page 137. 38 About Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
38
About Your System
Caution!
NVRAM_CLR jumper
is installed on
system board
NVRAM_CLR jumper is
installed in the clear setting.
CMOS has been cleared.
Move the NVRAM_CLR
jumper to the default
position (pins 3 and 5).
See Figure 6-1 for jumper
location. Restart the
system and re-enter
the BIOS settings. See
"Using the System Setup
Program and UEFI Boot
Manager" on page 51.
CPU set to
minimum
frequency.
The processor speed may be
intentionally set lower for
power conservation.
If not an intentional setting,
check any other system
messages for possible causes.
CPU
x
installed
with no memory.
Memory modules are
required but not installed in
the indicated processor’s
memory slots.
Install memory modules for
the processor. See
"Expansion Cards" on
page 103.
Current boot mode
is set to UEFI.
Please ensure
compatible
bootable media is
available. Use
the system setup
program to change
the boot mode as
needed.
The system failed to boot
because UEFI boot mode
is enabled in BIOS and
the boot operating system
is non-UEFI.
Ensure that the boot mode
is set correctly and that
the proper bootable media
is available. See "Using the
System Setup Program and
UEFI Boot Manager" on
page 51.
Decreasing
available memory
Faulty or improperly
installed memory modules.
Reseat the memory modules.
See "Troubleshooting System
Memory" on page 137.
Table 1-2.
System Messages
(continued)
Message
Causes
Corrective Actions