Dell S6000 FTOS 9.0(2.0) Configuration Guide for the System - Page 652
PIM-SM with IGMPv2 versus PIM-SM with IGMPv3, Source 1
View all Dell S6000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 652 highlights
Figure 33-1. PIM-SM with IGMPv2 versus PIM-SM with IGMPv3 630 | PIM Source-Specific Mode (PIM-SSM) www.dell.com | support.dell.com R2(conf )#do show ip pim tib PIM Multicast Routing Table Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, A - Candidate for MSDP Advertisement K - Ack-Pending State Timers: Uptime/Expires Interface state: Interface, next-Hop, State/Mode (*, 239.0.0.2), uptime 00:02:19, expires 00:03:13, RP 10.11.12.2, flags: S Incoming interface: Null, RPF neighbor 0.0.0.0 Outgoing interface list: GigabitEthernet 2/11 Forward/Sparse 00:02:19/00:03:13 (10.11.5.2, 239.0.0.2), uptime 00:00:44, expires 00:02:51, flags: P Incoming interface: GigabitEthernet 2/31, RPF neighbor 10.11.23.2 Outgoing interface list: Source 2 10.11.1.2 interface GigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown interface GigabitEthernet 3/21 ip pim sparse-mode ip address 10.11.23.2/24 no shutdown Source 1 10.11.5.2 interface GigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.1.1/24 no shutdown interface GigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown R3(conf )#do show ip pim tib PIM Multicast Routing Table Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, A - Candidate for MSDP Advertisement K - Ack-Pending State Timers: Uptime/Expires Interface state: Interface, next-Hop, State/Mode (10.11.5.2, 239.0.0.1), uptime 00:00:21, expires 00:03:14, flags: FT Incoming interface: GigabitEthernet 3/1, RPF neighbor 0.0.0.0 Outgoing interface list: GigabitEthernet 3/11 Forward/Sparse 00:00:15/00:03:15 2/1 interface GigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown R1(conf )#do show ip pim tib PIM Multicast Routing Table Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, A - Candidate for MSDP Advertisement K - Ack-Pending State Timers: Uptime/Expires Interface state: Interface, next-Hop, State/Mode RP interface GigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown R1 R2 3/1 2/31 3/21 R3 2/11 ip multicast-routing 3/11 ip pim rp-address 10.11.12.2 group-address 224.0.0.0/4 router rip network 10.0.0.0 1/21 1/31 interface GigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.1/24 no shutdown (10.11.5.2, 239.0.0.2), uptime 00:00:49, expires 00:03:04, flags: FT Incoming interface: GigabitEthernet 3/1, RPF neighbor 0.0.0.0 Outgoing interface list: GigabitEthernet 3/11 Forward/Sparse 00:00:49/00:02:41 interface GigabitEthernet 3/11 ip pim sparse-mode ip address 10.11.13.2/24 no shutdown (10.11.5.2, 239.0.0.1), uptime 00:00:02, expires 00:00:00, flags: CJ Incoming interface: GigabitEthernet 1/31, RPF neighbor 10.11.13.2 Outgoing interface list: Vlan 400 Forward/Sparse 00:00:02/Never (*, 239.0.0.2), uptime 00:02:12, expires 00:00:00, RP 10.11.12.2, flags: SCJ Incoming interface: GigabitEthernet 1/21, RPF neighbor 10.11.12.2 Outgoing interface list: Vlan 300 Forward/Sparse 00:02:12/Never interface Vlan 400 ip pim sparse-mode (10.11.5.2, 239.0.0.2), uptime 00:00:36, expires 00:03:14, flags: CT Incoming interface: GigabitEthernet 1/31, RPF neighbor 10.11.13.2 Outgoing interface list: Vlan 300 Forward/Sparse 00:02:12/Never ip address 10.11.4.1/24 untagged GigabitEthernet 1/2 ip igmp version 3 no shutdown ip igmp snooping enable Receiver 1 10.11.3.2 Group: 239.0.0.2 interface Vlan 300 ip pim sparse-mode ip address 10.11.3.1/24 untagged GigabitEthernet 1/1 no shutdown Receiver 2 10.11.4.2 Group: 239.0.0.1 Source: 10.11.5.2