Epson ActionNote 4SLC/33 User Manual - Page 152

Command prompt, CONFIG.SYS file, Configuration, Control code, Controller, Glossary 5

Get Epson ActionNote 4SLC/33 PDF manuals and user guides View all Epson ActionNote 4SLC/33 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 152 highlights

Command prompt The characters the operating system displays to indicate it is loaded and ready to receive instructions. The MS-DOS command prompt usually displays the current drive and directory with a greater-than symbol (A:\> or C:\>, for example). You can add other information to the command prompt using the PROMPT command, described in your MS-DOS manual. CONFIG.SYS file A special system file that MS-DOS executes each time you turn on or reset the computer. You use this file to customize your system by installing device drivers, setting limits for files and buffers, and specifying MS-DOS commands to be run during startup. Configuration The particular arrangement of the hardware components installed in or attached to your computer. For example, your configuration might include the built-in 3½-inch diskette drive, a hard disk, a trackball, and an internal modem. Control code A command (generated by holding down and pressing another key on the keyboard) that instructs the computer to perform a specific function. Controller A hardware component of your computer that manages the operation of the display, hard disk, or diskette drive. Glossary 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Command prompt
The characters the operating system displays to indicate it is
loaded and ready to receive instructions. The MS-DOS
command prompt usually displays the current drive and
directory with a greater-than symbol (A:\> or C:\>, for
example). You can add other information to the command
prompt using the PROMPT command, described in your
MS-DOS manual.
CONFIG.SYS file
A special system file that MS-DOS executes each time you turn
on or reset the computer. You use this file to customize your
system by installing device drivers, setting limits for files and
buffers, and specifying MS-DOS commands to be run during
startup.
Configuration
The particular arrangement of the hardware components
installed in or attached to your computer. For example, your
configuration might include the built-in 3½-inch diskette drive,
a hard disk, a trackball, and an internal modem.
Control code
A command (generated by holding d
own
and pressing
another key on the keyboard) that instructs the computer to
perform a specific function.
Controller
A hardware component of your computer that manages the
operation of the display, hard disk, or diskette drive.
Glossary 5