Epson Expression 636 User Manual - Page 12

If the power cord or plug is damaged; if liquid has entered

Get Epson Expression 636 PDF manuals and user guides View all Epson Expression 636 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

0 Use only the type of power source indicated on the scanner's label. 0 Connect all equipment to properly grounded power outlets. Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and off. 0 Place the scanner near a wall outlet where the plug can be easily unplugged. Placez le scannezu pres d'une de contacte 024 la fiche peut2tre debranchke facilement. 0 Do not let the power cord become damaged or frayed. 0 If you use an extension cord with the scanner, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cords ampere rating. Also, make sure the total of all devices plugged into the wall outlet does not exceed 15 amperes. 0 Except as specifically explained in this user's guide, do not attempt to service the scanner yourself. 0 Unplug the scanner and refer servicing to qualified service personnel under the following conditions: If the power cord or plug is damaged; if liquid has entered the scanner; if the scanner has been dropped or the cabinet damaged; if the scanner does not operate normally or exhibits a distinct change in performance. Adjust only those controls that are covered by the operating instructions. 0 If you plan to use the scanner in Germany, observe the following: To provide adequate short-circuit protection and overcurrent protection for this scanner, the building installation must be protected by a 16 Amp circuit breaker. Bei Anschluj3 des Scanners an die Stromversorgung muj3 sichergestellt werden, daj3 die Gebiiudeinstallation mit einem 16 A-Z&erstromschalter abgesichert ist. 6 Introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
0
Use only the type of power source indicated on the
scanner’s label.
0
Connect all equipment to properly grounded power
outlets. Avoid using outlets on the same circuit as
photocopiers or air control systems that regularly switch on
and off.
0
Place the scanner near a wall outlet where the plug can be
easily unplugged.
Placez
le
scannezu
pres
d’une
de
contacte
024
la fiche
peut-
2tre
debranchke
facilement.
0
Do not let the power cord become damaged or frayed.
0
If you use an extension cord with the scanner, make sure
the total ampere rating of the devices plugged into the
extension cord does not exceed the cords ampere rating.
Also, make sure the total of all devices plugged into the
wall outlet does not exceed 15 amperes.
0
Except as specifically explained in this user’s guide, do not
attempt to service the scanner yourself.
0
Unplug the scanner and refer servicing to qualified service
personnel under the following conditions:
If the power cord or plug is damaged; if liquid has entered
the scanner; if the scanner has been dropped or the cabinet
damaged; if the scanner does not operate normally or
exhibits a distinct change in performance. Adjust only those
controls that are covered by the operating instructions.
0
If you plan to use the scanner in Germany, observe the
following:
To provide adequate short-circuit protection and over-
current protection for this scanner, the building installation
must be protected by a 16 Amp circuit breaker.
Bei
Anschluj3
des Scanners an die
Stromversorgung
muj3
sichergestellt
werden,
daj3
die
Gebiiudeinstallation
mit einem
16
A-Z&erstromschalter
abgesichert ist.
6 Introduction