Epson TM-H6000IV with Validation Technical Reference Guide - Page 29

Product Overview, Do not use paper that has holes

Get Epson TM-H6000IV with Validation PDF manuals and user guides View all Epson TM-H6000IV with Validation manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 1 Product Overview • The slip paper must be flat, without curls or wrinkles, especially at the top edges. • When using slip paper with a glued area, choose it carefully, since paper feeding is affected by gluing conditions, such as position and dimension. OK to use Use carefully Use carefully Use carefully Paper inserting direction Glued area • Use thinner paper (N30 or equivalent) between the top and bottom sheets of multi-ply paper. If thick paper is used, the copy capability is lowered. • Do not use paper that has holes, or is translucent at the BOF sensor position. • Do not use paper that has holes or dark positions with low reflection (less than 40% 1 reflection) on the front at the TOF sensor position. 40 20 10 Paper inserting direction Area where holes are prohibited and reflection rate on the front should be 40% or more. [units: mm (All the numeric values are typical.)] • Do not use paper that has holes or dark positions with low reflection (less than 40% reflection) on the back at the validation sensor (only for the validation models). Paper inserting direction Area where holes are prohibited and reflection 7 rate on the front should be 20 40% or more. [units: mm (All the numeric values are typical.)] 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Chapter 1
Product Overview
29
1
•
The slip paper must be flat, without curls or wrinkles, especially at the top edges.
•
When using slip paper with a glued area, choose it carefully, since paper feeding is
affected by gluing conditions, such as position and dimension.
•
Use thinner paper (N30 or equivalent) between the top and bottom sheets of multi-ply
paper. If thick paper is used, the copy capability is lowered.
•
Do not use paper that has holes, or is translucent at the BOF sensor position.
•
Do not use paper that has holes or dark positions with low reflection (less than 40%
reflection) on the front at the TOF sensor position.
•
Do not use paper that has holes or dark positions with low reflection (less than 40%
reflection) on the back at the validation sensor (only for the validation models).
OK to use
Use carefully
Use carefully
Use carefully
Paper inserting direction
Glued area
40
20
10
Paper inserting
direction
Area where holes are
prohibited and reflection
rate on the front should be
40% or more.
[units: mm (All the numeric values are typical.)]
Paper inserting
direction
Area where holes are
prohibited and reflection
rate on the front should be
40% or more.
7
20
[units: mm (All the numeric values are typical.)]