Epson TM-H6000IV with Validation Technical Reference Guide - Page 92

Memory Switch Setting Mode, Starting the memory switch setting mode

Get Epson TM-H6000IV with Validation PDF manuals and user guides View all Epson TM-H6000IV with Validation manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Memory Switch Setting Mode In the memory switch setting mode, you can set the following "memory switches (customized values)," which are software switches of this printer. • Receipt print density • Transmission speed for serial interface • Automatic paper reduction • Autocutting at roll paper cover close • Roll paper width • Interface selection • Power supply unit capacity • Receipt print speed • Error control • Power on notice • NV capacity (User NV memory, NV graphics memory) • Command execution during offline For detailed information about memory switches, see "Setting the Memory Switches/ Receipt Enhancement" on page 65. Starting the memory switch setting mode Follow the steps below to run this mode. 1 Install the roll paper. 2 Close all covers and the receipt unit. 3 While pressing the Feed button, turn the power on. (Keep pressing the button until the printer starts printing.) The printer starts printing the current status of the printer. With the Ethernet interface, before printing starts, it takes 6 seconds if the IP address is fixed and 13 seconds if the IP address is obtained with the automatic setting. (It may take longer, depending on the response time from the host.) When the printer finishes printing the printer status, the following message is printed and the Paper LED flashes. (The printer is now in the self-test wait mode.): "Select Modes by pressing Feed button. Continue SELF-TEST: Less than 1 second Mode Selection : 1 second or more" 4 Press the Feed button. (Keep pressing the button until the printer starts printing.) The printer starts printing instructions. 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
92
Memory Switch Setting Mode
I
n
t
he memory sw
it
ch se
tting
mode, yo
u
ca
n
se
t
t
he follow
ing
“memory sw
it
ches (c
u
s
t
om
i
zed
val
u
es),” wh
i
ch are sof
t
ware sw
it
ches of
t
h
i
s pr
int
er.
Starting the memory switch setting mode
Follow
t
he s
t
eps below
t
o r
un
t
h
i
s mode.
1
Install the roll paper.
2
Close all covers and the receipt unit.
3
While pressing the Feed button, turn the power on. (Keep pressing the
button until the printer starts printing.)
The pr
int
er s
t
ar
t
s pr
inting
t
he c
u
rre
nt
s
t
a
tu
s of
t
he pr
int
er.
Whe
n
t
he pr
int
er f
ini
shes pr
inting
t
he pr
int
er s
t
a
tu
s,
t
he follow
ing
messa
g
e
i
s pr
int
ed a
n
d
t
he
Paper LED
flashes. (The pr
int
er
i
s
n
ow
in
t
he self-
t
es
t
wa
it
mode.):
“Selec
t
Modes by press
ing
Feed b
utt
o
n
.
Co
ntinu
e SELF-TEST: Less
t
ha
n
1 seco
n
d
Mode Selec
ti
o
n
: 1 seco
n
d or more”
4
Press the Feed button. (Keep pressing the button until the printer starts
printing.)
The pr
int
er s
t
ar
t
s pr
inting
in
s
t
r
u
c
ti
o
n
s.
•
Receipt print density
•
Transmission speed for serial interface
•
Automatic paper reduction
•
Autocutting at roll paper cover close
•
Roll paper width
•
Interface selection
•
Power supply unit capacity
•
Receipt print speed
•
Error control
•
Power on notice
•
NV capacity
(User NV memory, NV graphics memory)
•
Command execution during offline
For detailed information about memory switches, see
"Setting the Memory Switches/
Receipt Enhancement" on page 65
.
With the Ethernet interface, before printing starts, it takes 6 seconds if the IP address is
fixed and 13 seconds if the IP address is obtained with the automatic setting. (It may take
longer, depending on the response time from the host.)