Epson TM-H6000IV with Validation Technical Reference Guide - Page 91

Receipt Enhancement Information Print Mode, Starting the R/E information print mode

Get Epson TM-H6000IV with Validation PDF manuals and user guides View all Epson TM-H6000IV with Validation manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Chapter 3 Application Development Information Receipt Enhancement Information Print Mode You can confirm the following information on the roll paper by running the R/E information mode: • Automatic top logo setting • Automatic bottom logo setting • Extended settings for automatic top/bottom logo Starting the R/E information print mode Follow the steps below to run this mode. 1 Install the roll paper. 2 Close all covers and the receipt unit. 3 While pressing the Feed button, turn the power on. (Keep pressing the button until the printer starts printing.) The printer starts printing the current status of the printer. With the Ethernet interface, before printing starts, it takes 6 seconds if the IP address is 3 fixed and 13 seconds if the IP address is obtained with the automatic setting. (It may take longer, depending on the response time from the host.) When the printer finishes printing the printer status, the following message is printed and the Paper LED flashes. (The printer is now in the self-test wait mode.): "Select Modes by pressing Feed button. Continue SELF-TEST: Less than 1 second Mode Selection : 1 second or more" 4 Press the Feed button. (Keep pressing the button until the printer starts printing.) The printer starts printing instructions. 5 After the printing has been completed, press the Feed button twice. 6 Press the Feed button again. (Keep pressing the button until the printer starts printing.) The printer starts printing the R/E information. Turn the power off and on to return to the normal mode. 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Chapter 3
Application Development Information
91
3
Receipt Enhancement Information Print Mode
Yo
u
ca
n
co
n
f
i
rm
t
he follow
ing
in
forma
ti
o
n
o
n
t
he roll paper by r
unning
t
he R/E
in
forma
ti
o
n
mode:
•A
ut
oma
ti
c
t
op lo
g
o se
tting
•A
ut
oma
ti
c bo
tt
om lo
g
o se
tting
• Ex
t
e
n
ded se
tting
s for a
ut
oma
ti
c
t
op/bo
tt
om lo
g
o
Starting the R/E information print mode
Follow
t
he s
t
eps below
t
o r
un
t
h
i
s mode.
1
Install the roll paper.
2
Close all covers and the receipt unit.
3
While pressing the Feed button, turn the power on. (Keep pressing the
button until the printer starts printing.)
The pr
int
er s
t
ar
t
s pr
inting
t
he c
u
rre
nt
s
t
a
tu
s of
t
he pr
int
er.
Whe
n
t
he pr
int
er f
ini
shes pr
inting
t
he pr
int
er s
t
a
tu
s,
t
he follow
ing
messa
g
e
i
s pr
int
ed a
n
d
t
he
Paper LED
flashes. (The pr
int
er
i
s
n
ow
in
t
he self-
t
es
t
wa
it
mode.):
“Selec
t
Modes by press
ing
Feed b
utt
o
n
.
Co
ntinu
e SELF-TEST: Less
t
ha
n
1 seco
n
d
Mode Selec
ti
o
n
: 1 seco
n
d or more”
4
Press the Feed button. (Keep pressing the button until the printer starts
printing.)
The pr
int
er s
t
ar
t
s pr
inting
in
s
t
r
u
c
ti
o
n
s.
5
After the printing has been completed, press the Feed button twice.
6
Press the Feed button again. (Keep pressing the button until the printer
starts printing.)
The pr
int
er s
t
ar
t
s pr
inting
t
he R/E
in
forma
ti
o
n
.
T
u
r
n
t
he power off a
n
d o
n
t
o re
tu
r
n
t
o
t
he
n
ormal mode.
With the Ethernet interface, before printing starts, it takes 6 seconds if the IP address is
fixed and 13 seconds if the IP address is obtained with the automatic setting. (It may take
longer, depending on the response time from the host.)