Fluke 225C Service Manual - Page 74

Possible error messages., WarmingUp CL 0200:IDLE

Get Fluke 225C PDF manuals and user guides View all Fluke 225C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Fluke 19xB-19xC-2x5C Service Manual Possible error messages. The following messages can be shown on the test tool display: WARNING: Calibration data not valid. Save data and exit maintenance mode? Proceed as follows: • If you did the WarmingUp and Pre-Calibration successfully (section 5.5), and you want to store the Pre-Calibration data before continuing with the Final Calibration: ⇒ Press YES. When turning the test tool off and on again, it will show the message: The instrument needs calibration. Please contact your service center. The calibration date and number will not be updated. You must continue with the Final Calibration! • To return to the Maintenance mode, if you want to repeat the complete calibration: ⇒ Press NO. Now press until the display shows WarmingUp (CL 0200):IDLE, and calibrate the test tool, starting at section 5.5. • If you want to exit and maintain the old calibration data: ⇒ Turn the test tool off. 5-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Fluke 19xB-19xC-2x5C
Service Manual
5-18
Possible error messages.
The following messages can be shown on the test tool display:
WARNING: Calibration data not valid.
Save data and exit maintenance mode?
Proceed as follows:
•
If you did the WarmingUp and Pre-Calibration successfully (section 5.5), and you
want to store the Pre-Calibration data before continuing with the Final Calibration:
⇒
Press
YES
.
When turning the test tool off and on again, it will show the message:
The instrument needs calibration.
Please contact your service center.
The calibration date and number will not be updated.
You must continue with the Final
Calibration!
•
To return to the Maintenance mode, if you want to repeat the complete calibration:
⇒
Press
NO
.
Now press
until the display shows
WarmingUp (CL 0200):IDLE
, and
calibrate the test tool, starting at section 5.5.
•
If you want to exit and maintain the old calibration data:
⇒
Turn the test tool off.