Home » Fujitsu Manuals » Hard Drives » Fujitsu MHT2030AT » Manual Viewer

Fujitsu MHT2030AT Manual/User Guide - Page 103

Fujitsu MHT2030AT - Mobile 30 GB Hard Drive Manual

UPC - 683728090579

View all Fujitsu MHT2030AT manuals

Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

5.3 Host Commands At command issuance (I/O registers setting contents) 1F7H(CM) 1F6H(DH) 1F5H(CH) 1F4H(CL) 1F3H(SN) 1F2H(SC) 1F1H(FR) 0 0 1 1 1 1 0 0 x L x DV Start head No. / LBA [MSB] Start cylinder No. [MSB] / LBA Start cylinder No. [LSB] / LBA Start sector No. / LBA [LSB] Transfer sector count xx At command completion (I/O registers contents to be read) 1F7H(ST) 1F6H(DH) 1F5H(CH) 1F4H(CL) 1F3H(SN) 1F2H(SC) 1F1H(ER) Status information x L x DV End head No. / LBA [MSB] End cylinder No. [MSB] / LBA End cylinder No. [LSB] / LBA End sector No. / LBA [LSB] 00 (*1) Error information *1 If the command is terminated due to an error, the remaining number of sectors of which data was not transferred is set in this register. (9) RECALIBRATE (X'10' to X'1F') This command performs the calibration. Upon receipt of this command, the device sets BSY bit of the Status register and performs a calibration. When the device completes the calibration, the device updates the Status register, clears the BSY bit, and generates an interrupt. This command can be issued in the LBA mode. C141-E192-02EN 5-29

Section	Page
Front Cover	1
FOR SAFE OPERATION	2
Revision History	3
Preface	5
Important Alert Items	9
Manual Organization	11
Contents	13
Illustrations	18
Figures	18
Tables	20
CHAPTER 1 Device Overview	21
1.1 Features	22
1.1.1 Functions and performance	22
1.1.2 Adaptability	22
1.1.3 Interface	23
1.2 Device Specifications	24
1.2.1 Specifications summary	24
1.2.2 Model and product number	25
1.3 Power Requirements	26
1.4 Environmental Specifications	28
1.5 Acoustic Noise	29
1.6 Shock and Vibration	29
1.7 Reliability	30
1.8 Error Rate	31
1.9 Media Defects	31
1.10 Load/Unload Function	31
1.11 Advanced Power Management	32
CHAPTER 2 Device Configuration	35
2.1 Device Configuration	36
2.2 System Configuration	37
2.2.1 ATA interface	37
2.2.2 1 drive connection	37
2.2.3 2 drives connection	38
CHAPTER 3 Installation Conditions	39
3.1 Dimensions	40
3.2 Mounting	41
3.3 Cable Connections	47
3.3.1 Device connector	47
3.3.2 Cable connector specifications	48
3.3.3 Device connection	48
3.3.4 Power supply connector (CN1)	49
3.4 Jumper Settings	49
3.4.1 Location of setting jumpers	49
3.4.2 Factory default setting	50
3.4.3 Master drive-slave drive setting	50
3.4.4 CSEL setting	51
3.4.5 Power Up in Standby setting	52
CHAPTER 4 Theory of Device Operation	53
4.1 Outline	54
4.2 Subassemblies	54
4.2.1 Disk	54
4.2.2 Spindle	54
4.2.3 Actuator	54
4.2.4 Air filter	55
4.3 Circuit Configuration	55
4.4 Power-on Sequence	58
4.5 Self-calibration	59
4.5.1 Self-calibration contents	59
4.5.2 Execution timing of self-calibration	60
4.5.3 Command processing during self-calibration	61
4.6 Read/write Circuit	61
4.6.1 Read/write preamplifier (PreAMP)	61
4.6.2 Write circuit	61
4.6.3 Read circuit	63
4.6.4 Digital PLL circuit	64
4.7 Servo Control	65
4.7.1 Servo control circuit	65
4.7.2 Data-surface servo format	68
4.7.3 Servo frame format	70
4.7.4 Actuator motor control	71
4.7.5 Spindle motor control	72
CHAPTER 5 Interface	75
5.1 Physical Interface	76
5.1.1 Interface signals	76
5.1.2 Signal assignment on the connector	77
5.2 Logical Interface	80
5.2.1 I/O registers	81
5.2.2 Command block registers	82
5.2.3 Control block registers	87
5.3 Host Commands	88
5.3.1 Command code and parameters	88
5.3.2 Command descriptions	92
5.3.3 Error posting	182
5.4 Command Protocol	184
5.4.1 PIO Data transferring commands from device to host	184
5.4.2 PIO Data transferring commands from host to device	187
5.4.3 Commands without data transfer	188
5.4.4 Other commands	190
5.4.5 DMA data transfer commands	190
5.5 Ultra DMA Feature Set	192
5.5.1 Overview	192
5.5.2 Phases of operation	193
5.5.3 Ultra DMA data in commands	193
5.5.4 Ultra DMA data out commands	198
5.5.5 Ultra DMA CRC rules	202
5.5.6 Series termination required for Ultra DMA	203
5.6 Timing	204
5.6.1 PIO data transfer	204
5.6.2 Multiword data transfer	205
5.6.3 Ultra DMA data transfer	206
5.6.4 Power-on and reset	219
CHAPTER 6 Operations	221
6.1 Device Response to the Reset	222
6.1.1 Response to power-on	222
6.1.2 Response to hardware reset	223
6.1.3 Response to software reset	225
6.1.4 Response to diagnostic command	226
6.2 Power Save	227
6.2.1 Power save mode	227
6.2.2 Power commands	229
6.3 Defect Processing	229
6.3.1 Spare area	229
6.3.2 Alternating processing for defective sectors	230
6.4 Read-ahead Cache	232
6.4.1 DATA buffer structure	232
6.4.2 Caching operation	233
6.4.3 Using the read segment buffer	235
6.5 Write Cache	239
6.5.1 Cache operation	239
Glossary	243
Acronyms and Abbreviations	247
Index	249
Comment Form	251