Home » Garmin Manuals » GPS » Garmin G1000H » Manual Viewer

Garmin G1000H Bell 407GX Cockpit Reference Guide - Page 131

MFD1 DB, Knob to select the System Status

Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Flight Instruments EICAS Nav/Com/ XPDR/Audio AFCS GPS Nav Flight Planning Appendix 4) Press the YES Softkey. The navigation database is copied to the SD card in the bottom card slot of the MFD. 5) After the navigation database files are copied to the bottom SD card, press any key to continue, as instructed. 7) Again, press any key to continue as instructed on the display. 8) Press the NO Softkey. The display now starts in normal mode. Since the database effective date is not yet valid, it should not be loaded as the active database. The display now starts in normal mode. Do not remove power while the display is starting. 9) Press the ENT Key to acknowledge the startup screen. 10) Turn the large FMS Knob to select the AUX Page group on the MFD. 11) Turn the small FMS Knob to select the System Status Page. 12) The new database is copied to the SD card in the bottom card slot of each PFD. Progress can be monitored in the SYNC STATUS field. When copying is finished, 'Complete' is displayed. NOTE: During the synchronization process, version differences between standby navigation databases will exist. This will result in the system displaying a 'DB Mismatch' alert for the standby navigation databases. This alert will remain until the next power cycle. 13) Turn system power OFF. 14) Remove the SD card from the top card slot of the MFD. 15) Turn system power ON. 16) Press the ENT Key to acknowledge the startup screen. 17) Turn the large FMS Knob to select the AUX Page group on the MFD. 18) Turn the small FMS Knob to select the System Status Page. 19) Press the Display Database Selection Softkey to show standby navigation database information for each display (MFD1 DB, PFD1 DB). Verify the correct standby navigation database cycle information is shown for each display. Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/ Alerts Appendix Index 190-01254-00 Rev. A Garmin G1000H™ Cockpit Reference Guide for the Bell 407GX 115

Section	Page
Flight Instruments	17
Selecting the Altimeter Barometric Pressure Setting	17
Selecting Standard Barometric Pressure (29.92 in Hg)	17
Change Altimeter Barometric Pressure Setting Units	17
Change Navigation Sources	17
Enable/Disable OBS Mode While Navigating with GPS	18
Enable heading Preset Mode	18
Disable heading Preset Mode	18
Generic Timer	19
Configure Vspeed Bugs Individually	19
Set Barometric Minimum Descent Altitude	19
Set Barometric/Radar Altimeter (RA Optional) Minimum Descent Altitude	20
Displaying Wind Data	20
Changing HSI Format	20
Engine Indication System	21
Engine Power and Speed Indications	23
Power Assurance Check	24
Crew Alerting System (CAS)	25
CAS Message Prioritization	26
Nav/Com/Transponder/Audio Panel	27
ADF Tuning (Optional)	27
DME Tuning (Optional)	27
Enter a Transponder Code	27
Selecting a COM Radio	27
Selecting a NAV Radio	28
NAV/COM Tuning	29
Digital Clearance Recorder and Player (Optional)	30
Intercom Volume and Squelch	30
Intercom Modes	31
Passenger Address Mode (PA Mode)	35
Split-PA Mode	36
Automatic Flight Control System	37
GPS Navigation	39
Direct-to Navigation	39
Activate a Stored Flight Plan	40
Activate a Flight Plan Leg	40
Stop Navigating a Flight Plan	41
Vertical Navigation (VNAV)	41
Flight Planning	43
Weight Planning	43
Trip Planning	43
Create a User Waypoint Defined by Latitude & Longitude	45
Create a User Waypoint Defined by Radials from Other Waypoints	46
Create a User Waypoint Defined by a Radial & Distance from Another Waypoint	48
Delete a User Waypoint	49
Create a Flight Plan	50
Import a Flight Plan from an SD Card	51
Insert a Waypoint in the Active Flight Plan	51
Enter an Airway in a Flight Plan	52
Invert An Active Flight Plan	53
Remove a Departure, Arrival, Approach, or Airway from a Flight Plan	53
Store a Flight Plan	54
Edit a Stored Flight Plan	54
Delete a Waypoint from the Flight Plan	54
Invert and Activate a Stored Flight Plan	55
Copy a Flight Plan	55
Delete a Flight Plan	55
Graphical Flight Plan Creation	56
Export a Flight Plan to an SD Card	56
Procedures	57
Load and Activate a Departure Procedure	57
Activate A Departure Leg	57
Load An Arrival Procedure	57
Activate An Arrival Leg	58
Load and/or Activate an Approach Procedure	58
Activate An Approach in the Active Flight Plan	59
Activate a Vector to Final Approach Fix	60
Activate A Missed Approach in the Active Flight Plan	60
Hazard Avoidance	61
Customizing the Hazard Displays on the Navigation Map	61
XM Weather (Optional)	61
Traffic Systems	64
Terrain Awareness & Warning System (HTAWS) Display	66
Additional Features	71
Synthetic Vision	71
Terminal Procedure Charts	72
AOPA Airport Directory	74
Satellite Telephone and Data Link Services (Optional)	75
System Data Logging (Optional)	89
XM® Radio Entertainment (Optional)	90
Auxiliary Video (Optional)	92
Abnormal Operation	95
Reversionary Mode	95
Abnormal COM Operation	95
Hazard Displays with Loss of GPS Position	95
Unusual Attitudes	96
Dead Reckoning	97
Annunciations & Alerts	99
Warning Messages	99
Caution Messages	99
Advisory Messages	101
Safe Operating Annunciation	101
HTAWS Alerts	102
HTAWS System Status Annunciations	103
Voice Alerts	104
MFD & PFD Message Advisories	105
Database Message Advisories	106
GMA 350H Message Advisories	108
GIA 63H Message Advisories	109
GEA 71H Message Advisories	111
GTX 33H Message Advisories	112
GRS 77H Message Advisories	112
GMU 44 Message Advisories	113
GSR 56H Message Advisories	113
GDL 59H Message Advisories	113
GDL 69AH Message Advisories	114
GDC 74H Message Advisories	114
GTS 800 Message Advisories	115
Miscellaneous Message Advisories	115
Flight Plan Import/Export Messages	119
Appendix	121
PFD Softkey Map	121
MFD Softkey Map	126
Loading Updated Databases	128

Match case Limit results 1 per page

Garmin G1000H

™

Cockpit Reference Guide for the Bell 407GX

190-01254-00 Rev. A

Appendix

115

Flight

Instruments

EICAS

Nav/Com/

XPDR/Audio

AFCS

GPS Nav

Flight

Planning

Procedures

Hazard

Avoidance

Additional

Features

Abnormal

Operation

Annun/

Alerts

Appendix

Index

Press the

YES

Softkey.

The navigation database is copied to the SD card in

the bottom card slot of the MFD.

After the navigation database ﬁles are copied to the bottom SD card, press

any key to continue, as instructed.

Again, press any key to continue as instructed on the display.

Press the

Softkey.

The display now starts in normal mode.

Since the

database effective date is not yet valid, it should not be loaded as the

active database.

The display now starts in normal mode.

Do not remove

power while the display is starting.

Press the

ENT

Key to acknowledge the startup screen.

10)

Turn the large

FMS

Knob to select the AUX Page group on the MFD.

11)

Turn the small

FMS

Knob to select the System Status Page.

12)

The new database is copied to the SD card in the bottom card slot of each

PFD.

Progress can be monitored in the SYNC STATUS ﬁeld.

When copying

is ﬁnished, ‘Complete’ is displayed.

NOTE:

During the synchronization process, version differences between

standby navigation databases will exist.

This will result in the system

displaying a ‘DB Mismatch’ alert for the standby navigation databases.

This

alert will remain until the next power cycle.

13)

Turn system power OFF.

14)

Remove the SD card from the top card slot of the MFD.

15)

Turn system power ON.

16)

Press the

ENT

Key to acknowledge the startup screen.

17)

Turn the large

FMS

Knob to select the AUX Page group on the MFD.

18)

Turn the small

FMS

Knob to select the System Status Page.

19)

Press the Display Database Selection Softkey to show standby navigation

database information for each display (

MFD1 DB

PFD1 DB

Verify the

correct standby navigation database cycle information is shown for each display.