Gateway 7400 System Manual (PDF Version) - Page 121

Peripheral/adapter problems

Get Gateway 7400 PDF manuals and user guides View all Gateway 7400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Peripheral/adapter problems The system does not recognize a SCSI device. Probable cause The device needs to be added as new hardware The SCSI ID may be invalid The SCSI chain is not properly terminated The device cables are not installed correctly Solution In the Control Panel window (Start | Settings | Control Panel), double-click Add New Hardware. Follow the on-screen instructions for adding the device. Assign an available SCSI ID to the device. Make sure the last device on the SCSI chain is terminated. Open the system and check all cables between the controller and the device. Install the cables correctly if necessary. The system does not recognize an adapter card. Probable cause The interrupt or I/O address is set incorrectly The card was not configured through the software The card was not installed correctly Solution Check the address configuration of the adapter card and make sure that it does not conflict with another card in the system. Configure the card with the appropriate software. Make sure that the jumpers are configured correctly, then reseat the card. Peripheral/adapter problems 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Peripheral/adapter problems
113
Peripheral/adapter problems
The system does not recognize a SCSI device.
The system does not recognize an adapter card.
Probable cause
Solution
The device needs to be
added as new hardware
In the Control Panel window (
Start
|
Settings
|
Control Panel
), double-click
Add New
Hardware
. Follow the on-screen instructions
for adding the device.
The SCSI ID may be invalid
Assign an available SCSI ID to the device.
The SCSI chain is not
properly terminated
Make sure the last device on the SCSI chain
is terminated.
The device cables are not
installed correctly
Open the system and check all cables
between the controller and the device. Install
the cables correctly if necessary.
Probable cause
Solution
The interrupt or I/O address
is set incorrectly
Check the address configuration of the adapter
card and make sure that it does not conflict
with another card in the system.
The card was not configured
through the software
Configure the card with the appropriate
software.
The card was not installed
correctly
Make sure that the jumpers are configured
correctly, then reseat the card.