Gateway 7400 System Manual (PDF Version) - Page 42

documentation for proper cable orientation.

Get Gateway 7400 PDF manuals and user guides View all Gateway 7400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

8 Remove the mounting rails from the hard drive. 9 Place the old drive in an antistatic bag or container, then place the new hard drive on a static-free surface with the top up and the connectors facing you. 10 Install the two drive mounting rails on the new hard drive, making sure the front rail extensions are to the front of the device. The rails are labeled. 11 Set the drive jumpers to the appropriate settings (refer to your drive documentation for jumper settings.) 12 Align the rails with the open bay at the bottom of the drive stack, then slide the drive into the stack until the locking tabs snap into place (make sure that the data and power connectors on the drive face the inside of the server). 13 Connect the power and data cables to the drive. (See the drive documentation for proper cable orientation.) 14 Replace the bezel. (See "Replacing the bezel" on page 28.) 15 Close the case. (See "Closing the case" on page 27.) 16 Reconnect the power cord, the modem cord, and all other external peripheral devices, then turn on the system. 34 Replacing and Adding System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
34
Replacing and Adding System Components
8
Remove the mounting rails from the hard drive.
9
Place the old drive in an antistatic bag or container, then place the new
hard drive on a static-free surface with the top up and the connectors
facing you.
10
Install the two drive mounting rails on the new hard drive, making sure
the front rail extensions are to the front of the device. The rails are
labeled.
11
Set the drive jumpers to the appropriate settings (refer to your drive
documentation for jumper settings.)
12
Align the rails with the open bay at the bottom of the drive stack, then
slide the drive into the stack until the locking tabs snap into place (make
sure that the data and power connectors on the drive face the inside of
the server).
13
Connect the power and data cables to the drive. (See the drive
documentation for proper cable orientation.)
14
Replace the bezel. (See
“
Replacing the bezel
”
on page 28.)
15
Close the case. (See
“
Closing the case
”
on page 27.)
16
Reconnect the power cord, the modem cord, and all other external
peripheral devices, then turn on the system.