HP 11622 HP Rack Options Installation Guide for the 11000 G2 Series Rack and t - Page 20

Installing the air duct assembly

Get HP 11622 PDF manuals and user guides View all HP 11622 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

b. Using an electric drill, drill one 2.38-mm (3/32-in) hole through the lower duct, in the location that you marked. c. Insert one M3.5 self-drilling screw through the holes in both the upper and lower ducts (2). Installing the air duct assembly WARNING: The rack air duct weighs approximately 22.5 kg (50 lb). To reduce the risk of personal injury or damage to the equipment: • Observe local occupational health and safety requirements and guidelines for manual material handling. • Use at least two people to lift and stabilize the product during installation or removal. • Use step stools to install the product to the top of the rack. Do not lift the air duct over your head. 1. Using a T-30 Torx screwdriver, remove the two screws in the rear corners of the rack, and then remove the bracket. 2. Slide the air duct toward the front of the rack, until the front edge slides under the metal slots on the top plate of the rack (1). 3. Place the bracket back into place (2). Air Duct kit 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Air Duct kit 20
b.
Using an electric drill, drill one 2.38-mm (3/32-in) hole through the lower duct, in the location that
you marked.
c.
Insert one M3.5 self-drilling screw through the holes in both the upper and lower ducts (2).
Installing the air duct assembly
WARNING:
The rack air duct weighs approximately 22.5 kg (50 lb). To reduce the risk of
personal injury or damage to the equipment:
•
Observe local occupational health and safety requirements and guidelines for manual
material handling.
•
Use at least two people to lift and stabilize the product during installation or removal.
•
Use step stools to install the product to the top of the rack. Do not lift the air duct over your
head.
1.
Using a T-30 Torx screwdriver, remove the two screws in the rear corners of the rack, and then remove
the bracket.
2.
Slide the air duct toward the front of the rack, until the front edge slides under the metal slots on the top
plate of the rack (1).
3.
Place the bracket back into place (2).