HP 11622 HP Rack Options Installation Guide for the 11000 G2 Series Rack and t - Page 84

Stabilizer kit, About this device, Kit contents, Required tools, Installing the stabilizer

Get HP 11622 PDF manuals and user guides View all HP 11622 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

Stabilizer kit About this device The Stabilizer kit provides stability and support and prevents possible tipping when you install, remove, or access equipment within the HP 11000 G2 Series Racks and Intelligent Series Racks. The stabilizer kit is either required or recommended, depending on your rack configuration. There are four stabilizer kit options. • The standard 600-mm (23.6 in) or 800-mm (31.5 in) front foot is required with deployments of stand-alone racks. Rack rows with four or more bayed racks, without a single rack-mountable component exceeding 99.8 kg (220 lb), do not need a stabilizer kit installed. • The heavy duty 600-mm (23.6 in) or 800-mm (31.5 in) front foot is required when a single rack-mountable component weighing 99.8 kg (220 lb) or more is installed in a stand-alone rack or in a rack belonging to a rack row of three or fewer bayed racks. Kit contents Item 600-mm (23.62-inch) Front stabilizer mount Stabilizer feet M8 x 30-mm bolt M8 flat washer Quantity 1 2 8 8 This kit might contain extra hardware for your convenience. Required tools The following tools are required for installation: • Ratchet with sockets • Adjustable wrench Installing the stabilizer NOTE: HP recommends using the side feet, provided with this kit, to stabilize stand-alone racks from the side. If you are stabilizing racks that are secured together with baying kits, the side feet are optional on either end of the row. 1. Raise the rack with leveling feet to align the front foot with the front caster plate. Stabilizer kit 84

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Stabilizer kit 84
Stabilizer kit
About this device
The Stabilizer kit provides stability and support and prevents possible tipping when you install, remove, or
access equipment within the HP 11000 G2 Series Racks and Intelligent Series Racks.
The stabilizer kit is either required or recommended, depending on your rack configuration. There are four
stabilizer kit options.
•
The standard 600-mm (23.6 in) or 800-mm (31.5 in) front foot is required with deployments of
stand-alone racks. Rack rows with four or more bayed racks, without a single rack-mountable
component exceeding 99.8 kg (220 lb), do not need a stabilizer kit installed.
•
The heavy duty 600-mm (23.6 in) or 800-mm (31.5 in) front foot is required when a single
rack-mountable component weighing 99.8 kg (220 lb) or more is installed in a stand-alone rack or in
a rack belonging to a rack row of three or fewer bayed racks.
Kit contents
Item
Quantity
600-mm (23.62-inch) Front stabilizer mount
1
Stabilizer feet
2
M8 x 30-mm bolt
8
M8 flat washer
8
This kit might contain extra hardware for your convenience.
Required tools
The following tools are required for installation:
•
Ratchet with sockets
•
Adjustable wrench
Installing the stabilizer
NOTE:
HP recommends using the side feet, provided with this kit, to stabilize stand-alone racks
from the side. If you are stabilizing racks that are secured together with baying kits, the side feet
are optional on either end of the row.
1.
Raise the rack with leveling feet to align the front foot with the front caster plate.