HP 8100C HP Digital Sender 8100C - (English) Administrator Guide, C7707-90006 - Page 41

HPDigital Sender 8100C Administrator's Password, Factory defaults

Get HP 8100C - Digital Sender - Document Scanner PDF manuals and user guides View all HP 8100C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

39 1 Make sure the digital sender is idle. 2 At the control panel, press SETUP (ALT+F4). Then press SETTINGS (F2). 3 Select any of the configuration menus. If an administrator password is required, the HP Digital Sender 8100C Administrator's Password dialog box appears. Type the password and press OK (F1). 4 When the configuration menu appears, press TOOLS (F2). 5 Select Factory defaults and press OK (F1). 6 Press OK (F1) to confirm that you want to reset to factory defaults. At any time, you can check the database of address books to correct problems and inconsistencies in the information. Perform the database check for the following reasons: when the digital sender seems to be performing slowly for no apparent reason when the digital sender was inadvertently turned off during a sensitive operation (such as saving configuration changes) when you detect inconsistencies between address books and distribution lists when instructed to do so by troubleshooting steps or by HPcustomer support Notes about the procedure: The procedure causes the digital sender to shut down and then restart. The procedure can take as long as 25 minutes, based on the amount of information in address books. Note If the check fails, turn the digital sender off and back on, and then try again. If the problem persists, the address book database is beyond recovery. Clear the address book database (see pag e40).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
0·¿º³ºÁ´µÂ´¶µ±´¶¶ÄÁ
±
39
Ƚ·¿¹º¹»·»½·À´É»½¿%·¸¹À´Ë¶»º
1
Make sure the digital sender is idle.
2
At the control panel, press
S
ETUP
(
A
LT
+
F4
). Then press
S
ETTINGS
(
F2
)
.
3
Select any of the configuration menus. If an administrator password is required, the
HPDigital Sender 8100C Administrator’s Password
dialog box appears.
Type the password and press
O
K
(
F1
).
4
When the configuration menu appears, press
T
OOLS
(
F2
).
5
Select
Factory defaults
and press
O
K
(
F1
).
6
Press
O
K
(
F1
) to confirm that you want to reset to factory defaults.
’Dz÷»¼½¸³Ç²¸ºÂ¶²¾¾¸Ìµµ·¸Âº³ºÌº¾²
At any time, you can check the database of address books to correct problems and
inconsistencies in the information.
Perform the database check for the following reasons:
●
when the digital sender seems to be performing slowly for no apparent reason
●
when the digital sender was inadvertently turned off during a sensitive operation
(such as saving configuration changes)
●
when you detect inconsistencies between address books and distribution lists
●
when instructed to do so by troubleshooting steps or by HPcustomer support
Notes about the procedure:
●
The procedure causes the digital sender to shut down and then restart.
●
The procedure can take as long as 25 minutes, based on the amount of information
in address books.
Note
If the check fails, turn the digital sender off and back on, and then try again. If the problem
persists, the address book database is beyond recovery. Clear the address book database
(see pag e40)
.