HP D2D110 HP StorageWorks D2D Backup System User Guide (EH880-90950, October 2 - Page 119

Removing the hard drive, Installing a hard drive

Get HP D2D110 PDF manuals and user guides View all HP D2D110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

NOTE: If the replacement drive is not supplied with screws, remove the screws (two on each side) from the failed drive. Figure 45 Removing the hard drive 10. Replace the failed disk with the new disk. Insert the four drive screws (two on each side) into the hard drive (1). If these are not supplied with the new disk, use the screws from the failed disk. Slide the new hard drive (2) into the selected bay until it clicks into place. Connect the power cable from the power supply to the back of the hard drive and plug in the SATA cable (3). Figure 46 Installing a hard drive 11. Replace the drive cover. a. Replace the cover. b. Use the screw removed in step 7 to secure it. D2D Backup System 119

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
NOTE:
If the replacement drive is not supplied with screws, remove the screws (two on each side) from the
failed drive.
Figure 45 Removing the hard drive
10.
Replace the failed disk with the new disk.
Insert the four drive screws (two on each side) into the hard drive (1). If these are not supplied with
the new disk, use the screws from the failed disk. Slide the new hard drive (2) into the selected bay
until it clicks into place. Connect the power cable from the power supply to the back of the hard
drive and plug in the SATA cable (3).
Figure 46 Installing a hard drive
11.
Replace the drive cover.
a.
Replace the cover.
b.
Use the screw removed in step 7 to secure it.
D2D Backup System
119