HP D2D110 HP StorageWorks D2D Backup System User Guide (EH880-90950, October 2 - Page 30

Removing the access panel and bezel, Remove the access panel from the HP D2D Backup System.

Get HP D2D110 PDF manuals and user guides View all HP D2D110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

1. If you have already powered up the HP D2D Backup System, power it down and disconnect the cables before you start. 2. Remove the access panel from the HP D2D Backup System. 3. Install the HBA. 4. Install an internal tape drive and connect it to the HBA (if required). 5. Replace the access panel on the HP D2D Backup System. 6. Connect an external tape drive (if required). Please refer to the "User Guide" that is supplied with the tape drive for more detailed information about tape drive cabling and LED troubleshooting. Removing the access panel and bezel 1. If you are installing the tape drive as part of the initial installation, go to step 3. If you have already powered on the HP D2D Backup System, it must be shut down before you start. Make sure there are no backup or restore jobs in progress and that no future jobs are scheduled to start whilst the system is shut down. Select Shutdown on the Web Management interface and click Power Off to power down the HP D2D Backup System safely. 2. Disconnect the network cable and the power cord from the HP D2D Backup System. 3. Loosen the captive thumbscrew (1) located on the rear edge of the access panel and slide (2) the panel back about 2.5 cm (1.0 in). Remove the access panel. Figure 11 Removing the access panel 4. Press in on the two bottom tabs (1) on the side of the bezel so that they release from the chassis. Press in on the upper tab on the side of the bezel so that it releases from the chassis. The bezel will rotate out slightly (2). Pull the bezel away from the front panel (3). 30 Attaching a physical tape drive (optional)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
1.
If you have already powered up the HP D2D Backup System, power it down and disconnect the
cables before you start.
2.
Remove the access panel from the HP D2D Backup System.
3.
Install the HBA.
4.
Install an internal tape drive and connect it to the HBA (if required).
5.
Replace the access panel on the HP D2D Backup System.
6.
Connect an external tape drive (if required).
Please refer to the “User Guide” that is supplied with the tape drive for more detailed information about
tape drive cabling and LED troubleshooting.
Removing the access panel and bezel
1.
If you are installing the tape drive as part of the initial installation, go to step 3. If you have already
powered on the HP D2D Backup System, it must be shut down before you start. Make sure there
are no backup or restore jobs in progress and that no future jobs are scheduled to start whilst the
system is shut down. Select
Shutdown
on the Web Management interface and click
Power Off
to
power down the HP D2D Backup System safely.
2.
Disconnect the network cable and the power cord from the HP D2D Backup System.
3.
Loosen the captive thumbscrew (
1
) located on the rear edge of the access panel and slide (
2
) the
panel back about 2.5 cm (1.0 in). Remove the access panel.
Figure 11 Removing the access panel
4.
Press in on the two bottom tabs (
1
) on the side of the bezel so that they release from the chassis.
Press in on the upper tab on the side of the bezel so that it releases from the chassis. The bezel will
rotate out slightly (
2
). Pull the bezel away from the front panel (
3
).
30
Attaching a physical tape drive (optional)