HP D2D110 HP StorageWorks D2D Backup System User Guide (EH880-90950, October 2 - Page 29

Attaching a physical tape drive(optional), Hardware requirements for Tape Attach, Tape drive

Get HP D2D110 PDF manuals and user guides View all HP D2D110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

3 Attaching a physical tape drive (optional) In this chapter: • "Hardware requirements" on page 29 • "Tape drive installation overview" on page 29 • "Removing the access panel and bezel" on page 30 • "Installing the HBA" on page 31 • "Installing an internal tape drive" on page 33 • "Replacing the access panel and bezel" on page 35 • "Attaching an external tape drive" on page 36 Hardware requirements for Tape Attach A tape drive may be attached directly to your HP D2D Backup System, allowing you to store backups offsite. Figure 10 Attaching a tape drive to the HP D2D Backup System 1. Internal tape drive 2. External tape drive To use this facility you need: • A tape drive, such as an HP StorageWorks Ultrium device. This should be a half-height tape drive, if it is to be installed internally. Both SAS and SCSI tape drives are supported. • A host bus adapter, HBA for the tape drive connection (because there are no embedded SAS or SCSI ports). If the tape drive is pre-installed, an appropriate HBA is already installed. If not, you must purchase and install the HBA before connecting the tape drive. • Please refer to www.hp.com/go/connect for a list of all supported host bus adapters and tape drives. No additional drivers are required for recommended HBAs and tape drives; they are included in the HP D2D Backup System firmware. Please refer to "Export, import and copy to an attached tape drive" on page 83 more information about transferring data to the tape drive. Tape drive installation overview Before connecting either an internal or internal tape drive, you must install an HBA. All necessary cables for connecting to the HBA are supplied with the tape drive. The instructions in this chapter provide the following information that is specific to the HP D2D Backup System: D2D Backup System 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
3 Attaching a physical tape drive
(optional)
In this chapter:
•
“
Hardware requirements
” on page 29
•
“
Tape drive installation overview
” on page 29
•
“
Removing the access panel and bezel
” on page 30
•
“
Installing the HBA
” on page 31
•
“
Installing an internal tape drive
” on page 33
•
“
Replacing the access panel and bezel
” on page 35
•
“
Attaching an external tape drive
” on page 36
Hardware requirements for Tape Attach
A tape drive may be attached directly to your HP D2D Backup System, allowing you to store backups
offsite.
Figure 10 Attaching a tape drive to the HP D2D Backup System
1. Internal tape drive
2. External tape drive
To use this facility you need:
•
A tape drive, such as an HP StorageWorks Ultrium device. This should be a half-height tape drive, if it
is to be installed internally. Both SAS and SCSI tape drives are supported.
•
A host bus adapter, HBA for the tape drive connection (because there are no embedded SAS or SCSI
ports). If the tape drive is pre-installed, an appropriate HBA is already installed. If not, you must
purchase and install the HBA before connecting the tape drive.
•
Please refer to
w
w
w
.
h
p
.
c
o
m
/
g
o
/
c
o
n
n
e
c
t
for a list of all supported host bus adapters and tape drives.
No additional drivers are required for recommended HBAs and tape drives; they are included in
the HP D2D Backup System
fi
rmware.
Please refer to “
Export, import and copy to an attached tape drive
” on page 83 more information
about transferring data to the tape drive.
Tape drive installation overview
Before connecting either an internal or internal tape drive, you must install an HBA. All necessary cables
for connecting to the HBA are supplied with the tape drive. The instructions in this chapter provide the
following information that is speci
fi
c to the HP D2D Backup System:
D2D Backup System
29