HP ENVY Rove 20-k014us HP ENVY Rove 20 Mobile All-in-One PC - Maintenance and - Page 46

USB connector cable, Remove the Phillips PM2.5×3.0 screw

Get HP ENVY Rove 20-k014us PDF manuals and user guides View all HP ENVY Rove 20-k014us manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

5. Remove the media card reader board (5) and cable. Reverse this procedure to install the media card reader board. USB connector cable NOTE: The USB connector cable is included in the Cable Kit, spare part number 728048-001. See Cable Kit on page 12 for more Cable Kit information. Before removing the USB connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 23). 5. Remove the rear cover (see Rear cover on page 26). 6. Disconnect the battery cable (see Hard drive on page 27). 7. Remove the cover bracket (see X-axis capacitor board on page 33). 8. Remove the X-axis capacitor board (see X-axis capacitor board on page 33). 9. Remove the converter board (see Converter board on page 35). 10. Remove the media card reader board (see Media card reader board on page 37). Remove the USB connector cable: 1. Disconnect the USB connector cable (1) from the system board. 2. Release the USB connector cable (2) from the clips built into the middle frame. 3. Remove the Phillips PM2.5×3.0 screw (3) that secures the USB connector cable to the display assembly. 38 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
5.
Remove the media card reader board
(5)
and cable.
Reverse this procedure to install the media card reader board.
USB connector cable
NOTE:
The USB connector cable is included in the Cable Kit, spare part number 728048-001. See
Cable Kit
on page
12
for more Cable Kit information.
Before removing the USB connector cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
23
).
5.
Remove the rear cover (see
Rear cover
on page
26
).
6.
Disconnect the battery cable (see
Hard drive
on page
27
).
7.
Remove the cover bracket (see
X-axis capacitor board
on page
33
).
8.
Remove the X-axis capacitor board (see
X-axis capacitor board
on page
33
).
9.
Remove the converter board (see
Converter board
on page
35
).
10.
Remove the media card reader board (see
Media card reader board
on page
37
).
Remove the USB connector cable:
1.
Disconnect the USB connector cable
(1)
from the system board.
2.
Release the USB connector cable
(2)
from the clips built into the middle frame.
3.
Remove the Phillips PM2.5×3.0 screw
(3)
that secures the USB connector cable to the
display assembly.
38
Chapter 4
Removal and replacement procedures