HP ENVY Rove 20-k014us HP ENVY Rove 20 Mobile All-in-One PC - Maintenance and - Page 51

from the battery. The power button board

Get HP ENVY Rove 20-k014us PDF manuals and user guides View all HP ENVY Rove 20-k014us manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Before removing the power button board, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 23). 5. Remove the rear cover (see Rear cover on page 26). 6. Disconnect the battery cable (see Hard drive on page 27). 7. Remove the hard drive (see Hard drive on page 27). 8. Remove the cover bracket (see X-axis capacitor board on page 33). 9. Remove the display stand recess (see Display stand recess on page 41). Remove the power button board: 1. Release the ZIF connector (1) to which the power button board ribbon cable is attached, and then disconnect the power button board ribbon cable from the system board. 2. Detach the power button board ribbon cable (2) from the battery. (The power button board ribbon cable is attached to the battery with double-sided adhesive.) 3. Remove the two Phillips PM2.0×2.5 broad head screws (3) that secure the power button board to the display assembly. 4. Remove the power button board (4) and cable. Reverse this procedure to install the power button board. Component replacement procedures 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Before removing the power button board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
23
).
5.
Remove the rear cover (see
Rear cover
on page
26
).
6.
Disconnect the battery cable (see
Hard drive
on page
27
).
7.
Remove the hard drive (see
Hard drive
on page
27
).
8.
Remove the cover bracket (see
X-axis capacitor board
on page
33
).
9.
Remove the display stand recess (see
Display stand recess
on page
41
).
Remove the power button board:
1.
Release the ZIF connector
(1)
to which the power button board ribbon cable is attached, and
then disconnect the power button board ribbon cable from the system board.
2.
Detach the power button board ribbon cable
(2)
from the battery. (The power button board
ribbon cable is attached to the battery with double-sided adhesive.)
3.
Remove the two Phillips PM2.0×2.5 broad head screws
(3)
that secure the power button board
to the display assembly.
4.
Remove the power button board
(4)
and cable.
Reverse this procedure to install the power button board.
Component replacement procedures
43