HP Integrity Superdome 2 8/16 HP Smart Update Manager 5.0 User Guide - Page 9

Minimum requirements for Red Hat Enterprise Linux 6 servers, For SLES 11 AMD64/EM64T servers

Get HP Integrity Superdome 2 8/16 PDF manuals and user guides View all HP Integrity Superdome 2 8/16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

o e2fsprogs-32bit • For SLES 11 x86 servers: o libstdc++33-3.3.3-11.9.i586 or later o libnl (required for QLogic and Emulex drivers) • For SLES 11 AMD64/EM64T servers: o libstdc++33-32bit-3.3.3-11.9 or later o libnl (required for QLogic and Emulex drivers) Minimum requirements for Red Hat Enterprise Linux 6 servers NOTE: The following versions listed are needed as a minimum. Later versions of these might be used as well. NOTE: Ensure that each NIC has an IP address assigned. To get the IP address assigned to a NIC, enter the dhclient command in the console, which enables the NIC interfaces and retrieves an IP address. If a NIC does not have an IP address, HP SUM appears to hang on start up. • RHEL6 console mode NOTE: No X console in either x86 or x86_64 servers. To run HP SUM in silent mode, you must install the base server with defaults and the following RPMs. o lm_sensors-libs-3.1.1-10.el6..rpm o net-snmp-libs-5.5-27.el6..rpm o net-snmp-5.5.27.el6..rpm o kernel-headers-2.6.32-71.el6..rpm o redhat-rpm-config-9.0.3-25.el6.noarch.rpm o kernel-devel-2.6.32-71.el6..rpm o rpm-build-4.8.0-12.el6..rpm o gcc-4.4.4-13.el6..rpm • RHEL6 graphical mode NOTE: If the user elects to install the XWindows support, then the following steps apply to both x86 and x86_64 servers. NOTE: The following items must be the 32-bit version even under x86_64 architecture as HP SUM and several of the RPMs require 32-bit libraries installed. o libuuid-2.17.2-6.el6.i686.rpm o freetype-2.3.11-5.el6.i686.rpm o libSM-1.1.0-7.1.el6.i686.rpm o libICE-1.0.6-1.el6.i686.rpm o libXi-1.3-3.el6.i686.rpm o libX11-1.3-2.el6.i686.rpm o libXext-1.1-3.el6.i686.rpm Introduction 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Introduction 9
o
e2fsprogs-32bit
•
For SLES 11 x86 servers:
o
libstdc++33-3.3.3-11.9.i586 or later
o
libnl (required for QLogic and Emulex drivers)
•
For SLES 11 AMD64/EM64T servers:
o
libstdc++33-32bit-3.3.3-11.9 or later
o
libnl (required for QLogic and Emulex drivers)
Minimum requirements for Red Hat Enterprise Linux 6 servers
NOTE:
The following versions listed are needed as a minimum. Later versions of these might be
used as well.
NOTE:
Ensure that each NIC has an IP address assigned. To get the IP address assigned to a
NIC, enter the
dhclient
command in the console, which enables the NIC interfaces and
retrieves an IP address. If a NIC does not have an IP address, HP SUM appears to hang on start
up.
•
RHEL6 console mode
NOTE:
No X console in either x86 or x86_64 servers. To run HP SUM in silent mode, you must
install the base server with defaults and the following RPMs.
o
lm_sensors-libs-3.1.1-10.el6.<arch>.rpm
o
net-snmp-libs-5.5-27.el6.<arch>.rpm
o
net-snmp-5.5.27.el6.<arch>.rpm
o
kernel-headers-2.6.32-71.el6.<arch>.rpm
o
redhat-rpm-config-9.0.3-25.el6.noarch.rpm
o
kernel-devel-2.6.32-71.el6.<arch>.rpm
o
rpm-build-4.8.0-12.el6.<arch>.rpm
o
gcc-4.4.4-13.el6.<arch>.rpm
•
RHEL6 graphical mode
NOTE:
If the user elects to install the XWindows support, then the following steps apply to both
x86 and x86_64 servers.
NOTE:
The following items must be the 32-bit version even under x86_64 architecture as HP
SUM and several of the RPMs require 32-bit libraries installed.
o
libuuid-2.17.2-6.el6.i686.rpm
o
freetype-2.3.11-5.el6.i686.rpm
o
libSM-1.1.0-7.1.el6.i686.rpm
o
libICE-1.0.6-1.el6.i686.rpm
o
libXi-1.3-3.el6.i686.rpm
o
libX11-1.3-2.el6.i686.rpm
o
libXext-1.1-3.el6.i686.rpm