Home » HP Manuals » Servers » HP Integrity Superdome SX2000 » Manual Viewer

HP Integrity Superdome SX2000 HP Integrity Servers with Microsoft Windows Serv - Page 22

Fibre Channel

View all HP Integrity Superdome SX2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

• Unset the Administrator password. • Run EBSU from the EFI Shell instead of from the EFI Boot Manager. The EFI Shell can unblock the MPS Setting. EBSU fails when flashing an Emulex 4 Gb HBA Issue Servers Workaround EBSU cannot flash the Emulex 4 Gb Host Bus Adapter (HBA) to the latest firmware and EFI version, if the current EFI Driver flashed to the Emulex 4 Gb controller is version 5.02A1. All Integrity 1. Exit EBSU. 2. Unload all Emulex drivers using the EFI shell unload command. 3. Run EBSU again. ESBU can lose mapping of drives connected to QLogic controllers Issue Servers Workaround In some cases, EBSU may lose the mapping of disk drives attached to Qlogic controllers. All Integrity Use "Maintain Firmware" to flash the QLogic controller to the latest firmware. After reboot the system, EBSU detects and configures the disk drives attached to the QLogic controller. Express Setup fails when launched from EBSU Issue Servers Workaround The OS installer fails when launched by EBSU if the DVD drive is attached to a U320 controller. All Integrity 1. Exit EBSU. 2. Put the OS media in the DVD drive. 3. From the EFI Shell, issue the reconnect -r command followed by the map -r command. 4. Run the OS installer. Fibre Channel Installation causes MSA 1500 driver to be flagged Issue Servers Workaround A yellow exclamation mark (!) might be displayed for the HP StorageWorks 1000/MSA 1500 event notification driver after installing the Windows Server 2003 SP2 operating system using the 5.2 release reinstall media. All Integrity Using the Release 5.2 HP Smart Setup Media (SSM) CD, do one of the following: • Install the Support Pack (recommended). • Install HP StorageWorks MSA1000/MSA1500 Event Notification Driver component. Target LUN and boot controller WWN not visible in a VC environment Issue Servers When installing to storage attached to an Emulex LPe1105 mezzanine controller (403621-B21) in a Virtual Connect (VC) environment through a Brocade switch, the target LUN is not visible and the WWN for the boot controller is not visible in the zone in the switch administrative tool. HP Integrity BL860c Server Blade and BL870c Server Blade 22 Release 6.1 Overview

Section	Page
Release Notes	1
Table of Contents	3
About This Document	7
Typographic Conventions	7
HP Encourages Your Comments	7
1 Release 6.1 Overview	9
What’s New in Windows Solution 6.1?	9
System Configurations	9
Software Requirements	12
Web Browser	12
TCP/IP and SNMP	12
Utility Meter	12
Supported Components	12
Superdome (with sx1000 or sx2000 chipset)	12
rx8640	13
rx8620	14
rx7640	15
rx7620	16
rx6600	16
rx3600	17
rx2660	18
BL860c and BL870c Server Blade	18
Troubleshooting Common Issues	18
Application Development	19
Application hangs when calling the GetThreadContext function	19
Array Configuration Utility (ACU)	19
Verifer.exe causes ACU inaccuracies	19
Array Diagnostic Utility (ADU)	19
Uninstall feature not functional	19
Clustering	19
Cluster nodes unable to see messages	19
Device Drivers	19
Missing driver affects Virtual Machines	19
Drivers missing from Microsoft media	20
Driver roll back causes crash	20
prlntss.sys installation issue	20
Extensible Firmware Interface (EFI) and EFI-based Setup Utility (EBSU)	21
I/O card firmware values display as unknown	21
QLogic HBA firmware and EFI driver revisions display incorrectly	21
EBSU displays incorrect firmware version	21
EBSU changes EFI Boot menu	21
EBSU cannot change MPS settings if EFI password is set	21
EBSU fails when flashing an Emulex 4 Gb HBA	22
ESBU can lose mapping of drives connected to QLogic controllers	22
Express Setup fails when launched from EBSU	22
Fibre Channel	22
Installation causes MSA 1500 driver to be flagged	22
Target LUN and boot controller WWN not visible in a VC environment	22
Support Pack update generates errors	23
Inapplicable errors seen in kit update	23
Redundant entries seen in the Add/Remove Program	23
Emulex HBAs use different driver	23
MSA fails with Storport driver installed	24
LUNs undetected by ACU	24
HBA removal fails	24
HPSUM hangs on MSA 1500 boot	24
Hard Disk Configuration	24
Disk configuration lost after reboot	24
HP c-Class Blade System Infrastructure	25
Onboard Administrator displays wrong CPU	25
HP Smart Update Manager	25
Baseboard Management Controller IPMI device driver not displayed in HP-SUM	25
HPVM	25
Patches required on virtual machine guests	25
Installation	25
Attempting installation from a second DVD drive results in system message	25
Installation from graphics console might require additional steps	26
Hyper-threading might cause installation failure	26
Component time outs cause installation failure	26
Screen is blank at system startup	26
Use of 16 GB option discouraged	26
Maximum Payload Size parameter must be off	26
Use Esc+8 instead of F8 key on headless server	27
Custom Install option disables Remote Desktop	27
prlntss.sys requires Support Pack Installation	27
IP Console Switch use causes screen to blank	28
Management Agents	28
Error event after firmware update	28
Installation over the same version or older version is unsupported	28
Different port number reported by NIC Agents and NCU	28
Network Interface Cards (NICs)	29
Warning message not a cause for concern	29
Power Management	29
PAL_HALT_LIGHT disables idle power state	29
PAL_HALT_LIGHT status not displayed in HP-SUM, VCRM, and SMS	29
Partition Manager	29
C++ Runtime Library error message can be ignored	29
PXE boot on Intel Dual Core Itanium systems	29
Patch required to enable PXE boot	29
SCSI	30
Ultra 320 firmware update fails	30
Event log entry caused by timeout condition	30
Smart Array	30
640x/530x generates errors in system event log	30
6402 as internal disk drive controller generates errors	30
StorageWorks 43xx enclosures might cause errors	30
Configuration utility might be inaccessible	31
Tools menu radio buttons inactive	31
640x/530x might not load during system boot	31
640x/530x do not rebuild the internal HDD	32
640x hot add not supported	32
6400 cannot be hot-replaced during error message display	32
Command causes machine check abort	33
System Management Homepage (SMH)	33
Components flagged with red exclamation mark	33
Some components not shown	33
SMH fails to open	33
Program terminates after error message	34
Version Control	34
Some HP Integrity servers marked as non-compliant by Microsoft System Management Server	34
Baseboard Management Controller IPMI device driver not displayed in VCA	34
VCRM unsupported components	34
VCRM fails to start	35
VCRM updates wrong support pack	35
Inaccurate VGA information displayed	35
Video	35
Video not displayed	35
vKVM and vMedia	36
Tool bar fails to redraw as expected	36
vMedia drive not immediately accessible	36
vKVM session stops updating	36
2 Installing Windows Server 2003	37
Preinstallation Tasks	37
Installation Tasks	37
Reinstallation Tasks	38
Post-Installation Tasks	38
Tips and Tricks	38
3 Product Support	41
Technical Documentation	41
Technical Support	42
Get Windows-specific firmware, drivers, and utilities	42

Match case Limit results 1 per page

Unset the Administrator password.

•

Run EBSU from the EFI Shell instead of from the EFI Boot Manager. The

EFI Shell can unblock the MPS Setting.

EBSU fails when flashing an Emulex 4 Gb HBA

Issue

EBSU cannot flash the Emulex 4 Gb Host Bus Adapter (HBA) to the latest

firmware and EFI version, if the current EFI Driver flashed to the Emulex 4 Gb

controller is version 5.02A1.

Servers

All Integrity

Workaround

Exit EBSU.

Unload all Emulex drivers using the EFI shell

unload

command.

Run EBSU again.

ESBU can lose mapping of drives connected to QLogic controllers

Issue

In some cases, EBSU may lose the mapping of disk drives attached to Qlogic

controllers.

Servers

All Integrity

Workaround

Use "Maintain Firmware" to flash the QLogic controller to the latest firmware.

After reboot the system, EBSU detects and configures the disk drives attached

to the QLogic controller.

Express Setup fails when launched from EBSU

Issue

The OS installer fails when launched by EBSU if the DVD drive is attached to

a U320 controller.

Servers

All Integrity

Workaround

Exit EBSU.

Put the OS media in the DVD drive.

From the EFI Shell, issue the

reconnect -r

command followed by the

map -r

command.

Run the OS installer.

Fibre Channel

Installation causes MSA 1500 driver to be flagged

Issue

A yellow exclamation mark (

) might be displayed for the HP StorageWorks

1000/MSA 1500 event notification driver after installing the Windows Server

2003 SP2 operating system using the 5.2 release reinstall media.

Servers

All Integrity

Workaround

Using the Release 5.2 HP Smart Setup Media (SSM) CD, do one of the following:

•

Install the Support Pack (recommended).

•

Install HP StorageWorks MSA1000/MSA1500 Event Notification Driver

component.

Target LUN and boot controller WWN not visible in a VC environment

Issue

When installing to storage attached to an Emulex LPe1105 mezzanine controller

(403621-B21) in a Virtual Connect (VC) environment through a Brocade switch,

the target LUN is not visible and the WWN for the boot controller is not visible

in the zone in the switch administrative tool.

Servers

HP Integrity BL860c Server Blade and BL870c Server Blade

Release 6.1 Overview