HP LH4r HP Netserver LH 4 User Guide - Page 32

Installing Additional Memory in the LH 4r

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Chapter 5 Installing Additional Memory Figure 5-4. Inserting DIMM Into Memory Board 6. Repeat step 5 to install all of the DIMMs for your memory configuration. 7. Reinstall the memory boards. Memory A and Memory B need to be identical, so they are interchangeable in their sockets. 8. Close the memory cage cover and tighten the screw. 9. Replace the cover. 10. Restore electrical connections. Installing Additional Memory in the LH 4r NOTE How to change the memory in a racked NetServer depends on how high (or low) in the rack it is mounted. If there is room underneath the extended NetServer to reach up from below into the memory cage, the System board assembly can remain inside the NetServer. These instructions assume you need to remove the System board assembly. If you can reach the memory cage, proceed as for the LH 4. 1. Turn OFF the NetServer and remove all cables from the rear of the NetServer. Pull both power plugs out. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Chapter 5
Installing Additional Memory
26
Figure 5-4.
Inserting DIMM Into Memory Board
6.
Repeat step 5 to install all of the DIMMs for your memory configuration.
7.
Reinstall the memory boards. Memory A and Memory B need to be
identical, so they are interchangeable in their sockets.
8.
Close the memory cage cover and tighten the screw.
9.
Replace the cover.
10.
Restore electrical connections.
Installing Additional Memory in the LH 4r
NOTE
How to change the memory in a racked NetServer depends on
how high (or low) in the rack it is mounted. If there is room
underneath the extended NetServer to reach up from below
into the memory cage, the System board assembly can remain
inside the NetServer. These instructions assume you need to
remove the System board assembly.
If you can reach the memory cage, proceed as for the LH 4.
1.
Turn OFF the NetServer and remove all cables from the rear of the
NetServer. Pull both power plugs out.