HP LH4r HP Netserver LH 4 User Guide - Page 57

Attaching the Slides

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Chapter 8 Installing the NetServer in an HP Rack System/E or Rack System/U Figure 8-5. How to Attach Bar Nuts The slots in the mounting flange allow you to insert the flange in place behind the outside face but in front of the bar nut. Hold the bar nut behind the outside face of the column at the slide screw holes marked earlier. Start (but do not tighten) two screws through the face of the bar nut. Install the bar nuts on all four rack columns. The mounting flanges are then positioned behind the column face, but in front of the bar nuts. Attaching the Slides The slides have mounting flanges at each end (see Figure 8-6). The mounting flange is inserted between the column and the bar nut. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Chapter 8
Installing the NetServer in an HP Rack System/E or Rack System/U
51
Figure 8-5. How to Attach Bar Nuts
The slots in the mounting flange allow you to insert the flange in place behind
the outside face but in front of the bar nut.
Hold the bar nut behind the outside face of the column at the slide screw holes
marked earlier. Start (but do not tighten) two screws through the face of the bar
nut. Install the bar nuts on all four rack columns.
The mounting flanges are then positioned behind the column face, but in front of
the bar nuts.
Attaching the Slides
The slides have mounting flanges at each end (see Figure 8-6). The mounting
flange is inserted between the column and the bar nut.