HP LH4r HP Netserver LP 1000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 110

Clearing the CMOS Configuration, Switch 1 Position, Configuration Switch, Spring Latch, Battery

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Chapter 12 Troubleshooting Clearing the CMOS Configuration You may need to clear the CMOS configuration if the configuration has been corrupted, or if incorrect settings made in the Setup Utility have caused error messages to be unreadable. To clear the configuration: 1. Turn off power to the Netserver and remove the cover. 2. Move switch 4 in the configuration switch on the system board (labeled "Clear CMOS") to the ON position. See Figures 12-1 and 12-2. 3. Turn on power to the Netserver. A message displays indicating the configuration has been cleared. 4. Turn off power to the Netserver. 5. Return switch 4 on the system board to the OFF position. 6. Replace the cover. 7. Turn on power to the Netserver and the following message displays: Incorrect System Configuration 8. Press to run the Setup Utility when appears. 9. Make any configuration changes required. 10. Choose the Exit option and save the changes to save the configuration and exit the Setup Utility. Switch 1 Position Configuration Switch Spring Latch Battery Figure 12-1. Configuration Switch Location 104

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 12
Troubleshooting
104
Clearing the CMOS Configuration
You may need to clear the CMOS configuration if the configuration has been
corrupted, or if incorrect settings made in the Setup Utility have caused error
messages to be unreadable.
To clear the configuration:
1. Turn off power to the Netserver and remove the cover.
2. Move switch 4 in the configuration switch on the system board (labeled
"Clear CMOS") to the ON position. See Figures 12-1 and 12-2.
3. Turn on power to the Netserver.
A message displays indicating the configuration has been cleared.
4. Turn off power to the Netserver.
5. Return switch 4 on the system board to the OFF position.
6. Replace the cover.
7. Turn on power to the Netserver and the following message displays:
Incorrect System Configuration
8. Press <F2> to run the Setup Utility when
<
F2=Setup
>
appears.
9. Make any configuration changes required.
10. Choose the Exit option and save the changes to save the configuration and exit
the Setup Utility.
Switch 1 Position
Configuration Switch
Spring Latch
Battery
Figure 12-1. Configuration Switch Location