HP LH4r HP Netserver LP 1000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 59

it slightly to install both sides of the latch is acceptable.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 6 Installing an Additional Processor NOTE The heatsinks are not reusable unless the thermal patch has been replaced each time the heatsink is removed, even if the heatsink is just temporarily removed from a processor and then re-installed on the same processor. Each time the heatsink is moved (slide) on the processor, some of the thermal material is removed from the thermal patch, which could cause poor heat transfer and overheating. 3. Ensure the latches are free and pointing away from the heatsink. 4. Install the heatsink onto the processor in the following manner: CAUTION To prevent scratching off some of the thermal material, don't slide the heatsink around once it is on the processor. Rocking it slightly to install both sides of the latch is acceptable. a. Position the heatsink over the processor socket and lower it squarely onto the processor, as shown in Figures 6-5 and 6-6. The heatsink can only be installed in one direction, with the metal step to the left of processor socket, as shown in Figures 6-5 and 6-6. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 6
Installing an Additional Processor
53
NOTE
The heatsinks are not reusable unless the thermal patch has
been replaced each time the heatsink is removed, even if the
heatsink is just temporarily removed from a processor and then
re-installed on the same processor.
Each time the heatsink is moved (slide) on the processor, some
of the thermal material is removed from the thermal patch,
which could cause poor heat transfer and overheating.
3. Ensure the latches are free and pointing away from the heatsink.
4. Install the heatsink onto the processor in the following manner:
CAUTION
To prevent scratching off some of the thermal material, don't
slide the heatsink around once it is on the processor. Rocking
it slightly to install both sides of the latch is acceptable.
a.
Position the heatsink over the processor socket and lower it squarely onto
the processor, as shown in Figures 6-5 and 6-6.
The heatsink can only be installed in one direction, with the metal step to
the left of processor socket, as shown in Figures 6-5 and 6-6.