HP LH4r HP Netserver LP 1000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 76

Attaching the Front Bezel, Continuing with the Rack Installation Process

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Chapter 7 Rack Mounting the HP Netserver (2-Post) Attaching the Front Bezel The front bezel attaches to the HP Netserver by pivoting on two pins at the bottom and holding onto the top pins with spring latches. The middle pins force the bezel to rotate in or out, ensuring a rotating action. 1. Position the Bezel in front of the HP Netserver LP 1000r as shown in Figure 7-8. 2. Push in on the bottom to engage the pins, allowing it to rotate up. 3. Push the bezel in at the top to engage the spring latches. The spring latches should click when engaged. Pins Spring Latches (2) Figure 7-8. Installing the Bezel Continuing with the Rack Installation Process After you install the HP Netserver in the rack, refer to the white paper located on the HP web site for high-density rack configurations to continue with the process of installing and configuring the rack system. The white paper is titled HP Netserver High Density Rack Solutions Overview (LP 1000r and LP 2000r). 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 7
Rack Mounting the HP Netserver (2-Post)
70
Attaching the Front Bezel
The front bezel attaches to the HP Netserver by pivoting on two pins at the bottom
and holding onto the top pins with spring latches. The middle pins force the bezel
to rotate in or out, ensuring a rotating action.
1. Position the Bezel in front of the HP Netserver LP 1000r as shown in Figure
7-8.
2. Push in on the bottom to engage the pins, allowing it to rotate up.
3. Push the bezel in at the top to engage the spring latches.
The spring latches should click when engaged.
Pins
Spring
Latches (2)
Figure 7-8. Installing the Bezel
Continuing with the Rack Installation Process
After you install the HP Netserver in the rack, refer to the white paper located on
the HP web site for high-density rack configurations to continue with the process
of installing and configuring the rack system.
The white paper is titled
HP
Netserver High Density Rack Solutions Overview
(LP 1000r and LP 2000r)
.