HP StorageWorks MSA1510i HP Storage Management Utility user guide (383075-002, - Page 37

Sample con, guration status - after con, guring management and data ports, Data ports SA0, SA1, SB0

Get HP StorageWorks MSA1510i PDF manuals and user guides View all HP StorageWorks MSA1510i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

4. Select IP Address > Create Portal. 5. Enter settings for the portal. NOTE: For additional security, do not use commonly-known TCP ports. 6. When the display refreshes, verify that the newly configured portal is shown in the component list. 7. As needed for your environment, repeat Step 4 through Step 6 to assign additional TCP ports to this IP address. 8. Repeat Step 1 through Step 7 to add additional IP addresses to this data port or to configure the remaining data ports, such as SA1, SB0, and SB1. Sample configuration status - after configuring management and data ports Figure 10 illustrates the current configuration. The following items are configured: • Management port MA0 and MB0 • Data ports SA0, SA1, SB0, and SB1 • Each data port is assigned two (2) IP addresses • Each IP address is assigned two (2) TCP portals HP Storage Management Utility user guide 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
4.
Select
IP Address > Create Portal
.
5.
Enter settings for the portal.
NOTE:
For additional security, do not use commonly-known TCP ports.
6.
When the display refreshes, verify that the newly con
fi
gured portal is shown in the component list.
7.
As needed for your environment, repeat
Step 4
through
Step 6
to assign additional TCP ports to
this IP address.
8.
Repeat
Step 1
through
Step 7
to add additional IP addresses to this data port or to con
fi
gure the
remaining data ports, such as SA1, SB0, and SB1.
Sample con
fi
guration status - after con
fi
guring management and data ports
Figure 10
illustrates the current con
fi
guration.
The following items are con
fi
gured:
•
Management port MA0 and MB0
•
Data ports SA0, SA1, SB0, and SB1
•
Each data port is assigned two (2) IP addresses
•
Each IP address is assigned two (2) TCP portals
HP Storage Management Utility user guide
37