HP StorageWorks MSA1510i HP Storage Management Utility user guide (383075-002, - Page 52

disabled, enabled, Target, Enable/Disable Access Control, ACL State

Get HP StorageWorks MSA1510i PDF manuals and user guides View all HP StorageWorks MSA1510i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

2. Select Target > Enable/Disable Access Control. 3. Expand the ACL State drop-down box, and enable access control. 4. The following warning message is displayed: 5. Confirm that there is no active I/O on the target, and then click OK. IMPORTANT: • To prevent loss of access to the storage, ACLs should not be modified if there is an active session between the initiator and the target. Before enabling ACL for a target, open your iSCSI initiator software and verify that the target status is inactive or disconnected. • When access control is disabled (default), all initiators with access to the array controller can access the storage targets. (If CHAP authentication is set up, only initiators with verified CHAP secrets can access the storage.) • When access control is enabled, access to all mapped logical drives of the target is immediately blocked (Step 2 through Step 3), until ACLs are created for each mapped logical drive (Step 6 through Step 7). 52 Configure

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
2.
Select
Target
>
Enable/Disable Access Control
.
3.
Expand the
ACL State
drop-down box, and enable access control.
4.
The following warning message is displayed:
5.
Con
fi
rm that there is no active I/O on the target, and then click
OK
.
IMPORTANT:
•
To prevent loss of access to the storage, ACLs should not be modi
fi
ed if there is an active
session between the initiator and the target. Before enabling ACL for a target, open
your iSCSI initiator software and verify that the target status is inactive or disconnected.
•
When access control is
disabled
(default), all initiators with access to the array controller
can access the storage targets. (If CHAP authentication is set up, only initiators with
veri
fi
ed CHAP secrets can access the storage.)
•
When access control is
enabled
, access to all mapped logical drives of the target is
immediately blocked (
Step 2
through
Step 3
), until ACLs are created for each mapped
logical drive (
Step 6
through
Step 7
).
52
Con
fi
gure