HP StorageWorks MSA1510i HP Storage Management Utility user guide (383075-002, - Page 82

Update, Controller, Flash Firmware, Browse, place the MSA in Standby mode.

Get HP StorageWorks MSA1510i PDF manuals and user guides View all HP StorageWorks MSA1510i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

7. From within the SMU, select Update > Controller > Flash Firmware. 8. Under the Flash Firmware banner, click Browse and navigate to the location of the previously-obtained firmware file, and then click OK. 9. Wait for a completion message to display. For example, the following messages are displayed on the MSA controller LCD panel: MSA1510i updates: 307 FIRMWARE FLASH DONE MSA20 updates: 313 FIRMWARE FLASH DONE ON BOX (Each attached storage enclosure is updated one at a time, in sequential box number order.) NOTE: Do not interfere with or cancel the download process. Interrupting the download process might corrupt the firmware. 10. Restart the MSA and its attached storage enclosures storage system by doing the following (newly downloaded firmware cannot be accessed until the MSA is restarted): a. Press and hold down the MSA Power on/Standby button for approximately five seconds to place the MSA in Standby mode. b. Power off all storage enclosures attached to the MSA. c. Wait approximately two minutes to ensure that the hard disk drives in the enclosures stop rotating. d. Restart all storage enclosures attached to the MSA. e. Wait approximately four minutes to allow the enclosures to complete their startup routines. f. Press and release the MSA Power on/Standby button to restart the MSA. g. Wait (up to eight minutes) for the STARTUP COMPLETE message to display on the MSA controller LCD panel. 82 Update

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
7.
From within the SMU, select
Update
>
Controller
>
Flash Firmware
.
8.
Under the Flash Firmware banner, click
Browse
and navigate to the location of the previously-obtained
fi
rmware
fi
le, and then click
OK
.
9.
Wait for a completion message to display.
For example, the following messages are displayed on the MSA controller LCD panel:
MSA1510i updates:
307 FIRMWARE FLASH DONE
MSA20 updates:
313 FIRMWARE FLASH DONE ON BOX <n>
(Each attached storage enclosure is updated one at a time, in sequential box number
order.)
NOTE:
Do not interfere with or cancel the download process. Interrupting the download process
might corrupt the
fi
rmware.
10.
Restart the MSA and its attached storage enclosures storage system by doing the following (newly
downloaded
fi
rmware cannot be accessed until the MSA is restarted):
a.
Press and hold down the MSA Power on/Standby button for approximately
fi
ve seconds to
place the MSA in Standby mode.
b.
Power off all storage enclosures attached to the MSA.
c.
Wait approximately two minutes to ensure that the hard disk drives in the enclosures stop
rotating.
d.
Restart all storage enclosures attached to the MSA.
e.
Wait approximately four minutes to allow the enclosures to complete their startup routines.
f.
Press and release the MSA Power on/Standby button to restart the MSA.
g.
Wait (up to eight minutes) for the STARTUP COMPLETE message to display on the MSA
controller LCD panel.
82
Update