HP Surestore Tape Library Model 2/15 HP DLT Tape Library 15-Slot - (English) U - Page 61

Scsi Ids, Set Ids, Lib Bus1 Id, Update Ids Now, Wait For Update, Ids Saved, Conflict, Aborted

Get HP Surestore Tape Library Model 2/15 PDF manuals and user guides View all HP Surestore Tape Library Model 2/15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

NOTE Library Operation Specifying SCSI Addresses 3. Enter the three-part numerical password (see "Entering the Administration Menu Password" on page 4-7). 4. Press NEXT until SCSI IDs* displays, then press ENTER. 5. SET IDs* displays. Press ENTER. LIB BUS1 ID # or DRV# BUS# ID # displays. (LIB BUS1 ID # stands for the current SCSI ID of the robotics controller. DRV# BUS# ID # is the current SCSI ID setting for the drive number and its associated bus #.) 6. Press NEXT until the setting to change displays, then press ENTER. 7. The current SCSI address setting flashes. Press NEXT or PREV until the desired address displays, then press ENTER. 8. Press NEXT until UPDATE IDs NOW displays, then press ENTER. 9. WAIT FOR UPDATE displays briefly, then IDs SAVED displays. • If the new settings do not conflict with other SCSI IDs on the bus, SCSI IDs* displays. • If the new settings conflict with other IDs on the SCSI bus, CONFLICT ABORTED displays briefly, then SET IDs* displays. Any changes entered are lost, and previous steps must be repeated to set a new address. • If any buses are daisy chained together, make sure the SCSI IDs are different for each device on the bus. • If a serial communications error is detected while trying to set the SCSI IDs, DRV CONNECT ERR displays, followed by IDs NOT CHANGED. Any changes entered are lost. The SCSI IDs* menu displays. 10. Press CANCEL three times to return to the drive status ("ready" state). 11. To save new settings can be saved to flash ROM, turn the library off, then turn it back on. This allows the settings to be recovered if the library is powered off for more than ten days. After changing an address, it may be necessary to reboot the host for the new SCSI IDs to be recognized. Library Operation 4-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
4-11
Library Operation
Specifying SCSI Addresses
Library Operation
3.
Enter the three-part numerical password (see “Entering the
Administration Menu Password” on page 4-7).
4.
Press
NEXT
until
SCSI IDs*
displays, then press
ENTER
.
5.
SET IDs*
displays. Press
ENTER
.
LIB BUS1 ID #
or
DRV# BUS# ID #
displays. (LIB BUS1 ID # stands
for the current SCSI ID of the robotics controller.
DRV# BUS# ID # is the current SCSI ID setting for the drive number and
its associated bus #.)
6.
Press
NEXT
until the setting to change displays, then press
ENTER
.
7.
The current SCSI address setting flashes. Press
NEXT
or
PREV
until the
desired address displays, then press
ENTER
.
8.
Press
NEXT
until
UPDATE IDs NOW
displays, then press
ENTER
.
9.
WAIT FOR UPDATE
displays briefly, then
IDs SAVED
displays.
•
If the new settings do not conflict with other SCSI IDs on the bus,
SCSI IDs*
displays.
•
If the new settings conflict with other IDs on the SCSI bus,
CONFLICT
ABORTED
displays briefly, then
SET IDs*
displays. Any changes
entered are lost, and previous steps must be repeated to set a new
address.
•
If any buses are daisy chained together, make sure the SCSI IDs are
different for each device on the bus.
•
If a serial communications error is detected while trying to set the
SCSI IDs,
DRV CONNECT ERR
displays, followed by
IDs NOT
CHANGED
. Any changes entered are lost. The
SCSI IDs*
menu
displays.
10. Press
CANCEL
three times to return to the drive status (“ready” state).
11. To save new settings can be saved to flash ROM, turn the library off, then
turn it back on. This allows the settings to be recovered if the library is
powered off for more than ten days.
NOTE
After changing an address, it may be necessary to reboot the host for the new
SCSI IDs to be recognized.